Edwards Signaling 109 Series - Manual

P/N 3100392 ISSUE 1 © 2002
Installation Instructions for 109 Series
LED Star-Burst TM Visual Indicator
Description
The 109 Series Visual Indicator is a UL and cUL listed signaling
appliance in a NEMA 4X and IP65 rated enclosure. The modules
can be panel mounted or conduit mounted.
The visual indicator is normally steady-on and with a contact
closure, the light will flash. The unit is set for the Rapid Star-Burst
flicker flash but with a simple jumper change, can output a 65
flash per minute signal.
The visual indicators are available in red, blue, green, amber or
white.
Specifications
Panel Mounting (Figure 2)
Note: The integrity of the outdoor, NEMA 4X, and IP65 rating on
the panel assembly at the interface with the 109 Series Visual
Indicator relies on the construction and configuration details of
the mounting surface. Installer should evaluate.
1. Place the mounting gasket (supplied) over the hole in the
panel and route the signal wires through the gasket and the
hole in the panel.
2. Insert the base through the hole in the panel and screw the
locking nut (supplied), with the raised locking edge facing
the mounting surface, onto the base to secure the beacon.
3. Using wire nuts (not supplied), connect the signal's wire leads
as shown in Figure 1 or 2. Polarity must be observed on DC
models.
a. Connect the Red (DC models) or Black (AC models) wire
to hot.
b. Connect the Black (DC models) or White (AC models) to
common.
c. For steady-on applications, trim the yellow wire short
and cap using a wire nut (not supplied). For either Star-
Burst flicker flash or standard 65 fpm flash, connect the
yellow wire to hot to activate.
NOTE: On AC models only, the yellow can be connected
to hot, negative or ground to activate the Star-Burst
flicker flash or standard 65 fpm flash)
4. Turn on power and verify that the signal operates properly.
Jumper Installation
The 109 Series Visual Indicator is supplied with a default setting
of Star-Burst flicker flash. If a standard flash rate of 65 fpm is
desired, open the unit by removing (4) screws securing the lens to
the base and install jumper on pins 1-2 as shown in Figure 3.
Catalog LED
Number Voltage Current Color
109A-G1 24V DC 0.475 A Amber
109B-G1 24V DC 0.475 A Blue
109G-G1 24V DC 0.475 A Green
109R-G1 24V DC 0.475 A Red
109W-G1 24V DC 0.475 A White
109A-N5 120V 50/60 Hz 0.140 A Amber
109B-N5 120V 50/60 Hz 0.140 A Blue
109G-N5 120V 50/60 Hz 0.140 A Green
109R-N5 120V 50/60 Hz 0.140 A Red
109W-N5 120V 50/60 Hz 0.140 A White
Installation
Conduit Mounting (Figure 1)
1. Thread the 18" (45.7 cm) signal wire leads through either
1/2" (13mm) or 3/4" (19 mm) conduit into an approved conduit
outlet box. (Product is supplied with a double threaded - 1/2"
(13mm) internal and 3/4" (19mm) external - conduit hub.)
2. Using wire nuts (not supplied), connect the signal's wire leads
as shown in Figure 1. Polarity must be observed on DC models.
CHESHIRE, CT 203-699-3000 FAX 203-699-3365 (CUST. SERV.) 203-699-3078 (TECH. SERV.)
WARNING
To avoid risk of injury, install lens before energizing
the unit.
To avoid the risk of injury, do not remove or insert
light source when unit is energized.
WARNING
To prevent electrical shock, ensure that power is
turned off before installing the signal.
Figure 1. Conduit Mounting (3/4" Shown)
3. Thread the conduit onto the base of the signal.
4. Turn on power and verify that the signal operates properly.
109 Series Star-Burst
Visual Indicator
3/4" (19 mm) NPT
conduit (not supplied)
Black (DC common) or White (AC common)
Red (DC hot) or Black (AC hot)
Yellow (hot to activate
either the Star-Burst flicker flash or
standard 65 fpm flash)
Wire nuts
(not supplied)