Brocade FCX Series Hardware Installation Guide User Manual

Page 59

Modified CLI examples for the 2-port 10 Gbps SFP+ module

The following sample output from the show module command displays an entry
for the 2-port 10G SFP+ module.

device# show module

Module Status Ports Starting MAC

U1:M1 FCX-48GS POE 48-port Management Module OK 48 0024.38c9.4d00

U1:M2 FCX-2XGC 2-port 16G Module (2-CX4) OK 2 0024.38c9.4d31

U1:M3 FCX-2SFPP 2-port 10G Module (2-SFP+) OK 2 0024.38c9.4d33

The following sample output from the show version command shows that the 2-
port 10G SFP+ module is in slot 3.

device# show version

UNIT 1: compiled on Oct 18 2012 at 16:01:04 labeled as FCXS07300b1

(5373912 bytes) from Primary FCXS07300b1.bin

SW: Version 07.3.00b1T7f1

Boot-Monitor Image size = 370663, Version:07.3.00T7f5 (grz07300b1)

HW: Stackable FCX648S-HPOE-PREM (PROM-TYPE FCX-ADV-U)

==========================================================================

UNIT 1: SL 1: FCX-48GS POE 48-port Management Module

Serial #: BCYXXXXXXXX

License: BASE_SOFT_PACKAGE (LID: deaHHJIhFNb)

P-ENGINE 0: type DB90, rev 01

P-ENGINE 1: type DB90, rev 01

PROM-TYPE: FCX-ADV-U

==========================================================================

UNIT 1: SL 2: FCX-2XGC 2-port 16G Module (2-CX4)

==========================================================================

UNIT 1: SL 3: FCX-2SFPP 2-port 10G Module (2-SFP+)

==========================================================================

800 MHz Power PC processor 8544E (version 0021/0022) 400 MHz bus

65536 KB flash memory

256 MB DRAM

STACKID 1 system uptime is 2 days 10 minutes 24 seconds

The system : started=warm start reloaded=by "reload"

The following is sample output of the show running-config command.

device# show running-config

Startup-config data location is flash memory

Startup configuration:

ver 07.3.00a001T7f1

stack unit 1

module 1 fcx-48-poe-port-management-module

module 2 fcx-cx4-2-port-16g-module

module 3 fcx-sfpp-2-port-10g-module

The following is sample output of the show media and show optic commands
with some configuration.

device# show media

1/1/1:C 1/1/2:C 1/1/3:C 1/1/4:C 1/1/5:C 1/1/6:C 1/1/7:C 1/1/8:C

1/1/9:C 1/1/10:C 1/1/11:C 1/1/12:C 1/1/13:C 1/1/14:C 1/1/15:C 1/1/16:C

1/1/17:C 1/1/18:C 1/1/19:C 1/1/20:C 1/1/21:C 1/1/22:C 1/1/23:C 1/1/24:C

1/1/25:C 1/1/26:C 1/1/27:C 1/1/28:C 1/1/29:C 1/1/30:C 1/1/31:C 1/1/32:C

1/1/33:C 1/1/34:C 1/1/35:C 1/1/36:C 1/1/37:C 1/1/38:C 1/1/39:C 1/1/40:C

1/1/41:C 1/1/42:C 1/1/43:C 1/1/44:C 1/1/45:C 1/1/46:C 1/1/47:C 1/1/48:C

1/2/1:XG-CX4 1/2/2:XG-CX4

1/3/1:XG-SR 1/3/2:XG-SR

device# show media e 1/3/1

Port 1/3/1: Type : 10G XG-SR(SFP +)

Vendor: Brocade Version: 1

Part# : PLRXPLSCS4371 Serial#: CXXXXXXXX

device(config)# op 1

Enable optical monitoring and set alarm/warn interval to 1 minute(s)

Installing the FCX Switch

Brocade FCX Series Hardware Installation Guide

53-1003077-01