Yokogawa EJX440A - Manual (Page 34)

IM 01C25T03-01E 5-2
5. PARAMETER SUMMARY
No. Parameter name Item R/W Content
Applicable model
Upload
data
F P L
Default value
D AUX SET 1 Auxiliary setting data 1
D35 SP POINT Decimal place of static pressure W 0 to 4
D36 SP DAMPING Damping time constant of SP W 0.00 to 100.00 sec
D37 SP SELECT H/L select for static pressure W HIGH or LOW
D40 TEMP UNIT Temperature setting unit W degC, degF, or K
D50 QUICK RESP Quick response W OFF or ON (enable 0.00 to 0.50 sec at C30)
D55 WRT PROTECT Write protect indicator R NO or YES
D56 WRT ENABLE Write protect release W 8 alphanumeric characters
D57 NEW PASSWORD User set password for write protect W 8 alphanumeric characters
D58 SOFTWR SEAL Software seal R BREAK or KEEP
D60 SELF CHECK Self-diagnostics R See A60
E AUX SET 2 Auxiliary setting data 2
E10 T. ZERO CMP Temperature compensation mode W OFF or ON
E11 TEMP ZERO Zero shift compensation W Ϫ 99.999 to 99.999%/degC
E30 BI DIRE MODE Bidirectional mode W OFF or ON
E50 DO SELECT Contact output select W INHIBIT, PRES, SP, TEMP, PRES/SP,
PRES/TEMP, SP/TEMP, or PRES/SP/TEMP
E51 DO SIG. TYPE Signal type select W OFF WHEN ALARM or ON WHEN ALARM
E52 D OUTPUT Contact output R OFF or ON
E60 SELF CHECK Self-diagnostics R See A60
G ALARM SET Alarm setting
G10 P AL MODE Alert mode W INHIBIT, HI. AL DETECT, LO. AL DETECT,
or HI/LO. AL DETECT
G11 P HI. AL VAL High side alert value W Ϫ 32000 to 32000, unit specified in C20
G12 P LO. AL VAL Low side alert value W Ϫ 32000 to 32000, unit specified in C20
G20 SP AL MODE Static pressure alert mode W INHIBIT, HI. AL DETECT, LO. AL DETECT,
or HI/LO. AL DETECT
G21 SP HI. AL VAL High side alert value of SP * 2 W Ϫ 32000 to 32000, unit specified in D30
G22 SP LO. AL VAL Low side alert value of SP W Ϫ 32000 to 32000, unit specified in D30
G30 T AL MODE Temperature alert mode W INHIBIT, HI. AL DETECT, LO. AL DETECT,
or HI/LO. AL DETECT
G31 T HI. AL VAL High side alert value of temperature W Ϫ 50 to 130
G32 T LO. AL VAL Low side alert value of temperature W Ϫ 50 to 130
G50 AUTO RECOVER Auto-recover from sensor error W OFF or ON
G60 SELF CHECK Self-diagnostics R See A60
H AUTO SET Automatic setup
H10 AUTO P LRV Lower range value auto setup W Ϫ 32000 to 32000, unit specified in C20
H11 AUTO P URV Upper range value auto setup W Ϫ 32000 to 32000, unit specified in C20
H20 AUTO SP LRV SP lower range value auto setup W Ϫ 32000 to 32000, unit specified in D30
H21 AUTO SP URV SP upper range value auto setup * 2 W Ϫ 32000 to 32000, unit specified in D30
H60 SELF CHECK Self-diagnostics R See A60
I DISP SET Display setting
I10 DISP OUT1 LCD output 1 W PRES, PRES %, ENGR. PRES, SP, or SP %
I11 DISP OUT2 LCD output 2 W PRES, PRES %, ENGR. PRES, SP, SP %, or
---
I12 DISP OUT3 LCD output 3 W See I11
I13 DISP OUT4 LCD output 4 W See I11
I20 P DISP MODE % display mode W LINEAR or SQUARE ROOT
I21 PRES % RESO % display resolution W NORMAL or HIGH RESOLUTION
I30 ENGR. UNIT User set engineering unit W 8 alphanumeric characters
I31 EASY EU SET Engineering unit select W
I32 ENGR. EXP Exponents W ---, ϫ 10, ϫ 100, ϫ 1000
I33 ENGR. LRV User set lower range limit W Ϫ 32000 to 32000, unit specified in I30
I34 ENGR. URV User set upper range limit W Ϫ 32000 to 32000, unit specified in I30
I35 ENGR. POINT Decimal place of user set W 0 to 4
I40 BAR INDICATR Bar indicator W OFF or ON
I60 SELF CHECK Self-diagnostics R See A60
1
2.00 sec
HIGH
degC
OFF
NO
None
None
KEEP
OFF
0.000%/degC
OFF
INHIBIT
ON WHEN ALARM
OFF
INHIBIT
100.000 kPa
Ϫ 100.000 kPa
INHIBIT
0.00000 MPa
INHIBIT
120 degC
Ϫ 40 degC
ON
As specified
As specified
0.00000 MPa
PRES %
---
---
---
LINEAR
NORMAL
---
0.00
100.00
1
ON
● - ● ●
● - ● ●
● - ● ●
● ● ● ●
● ● ● ●
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● - ● -
● - ● -
● - ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● ● ● -
● - ● -
● - ● -
● ● ● -
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● -
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● ●
● ● ● -
* 1: R/W: R = Read only, W = Read & Write
* 2: The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.
* 1