Yokogawa EJX440A - Manual (Page 14)

IM 01C25T03-01E 3-6
3. OPERATION
3.2.3 Setting Parameters
Set or change the parameters as necessary. After
completing these, do not fail to use the “DIAG” key to
confirm that “GOOD” is displayed for the self-
diagnostic result at _
60: SELF CHECK .
(1) Tag No. Setup (C10: TAG NO)
Use the procedure below to change the Tag No. Up to
16 alphanumeric characters can be entered.
Press the key to turn on
the BT200.
Connect DPharp and BT200 using
a communication cable and press
the key.
PARAM
01:MODEL
EJX110 M
02:TAG NO.
YOKOGAWA
03:SELF CHECK
GOOD
OK
MENU
A:DISPLAY
B:SENSOR TYPE
C:BASIC SETUP
D:AUX SET1
E:AUX SET2
G:ALARM SET
HOME SET ADJ ESC
MENU
C:BASIC SETUP
D:AUX SET 1
E:AUX SET 2
G:ALARM SET
H:AUTO SET
I:DISP SET
HOME SET ADJ ESC
MENU
C10:TAG NO.
YOKOGAWA
C20:PRES UNIT
kPa
C21:PRES LRV
0.00000 kPa
DATA DIAG PRNT ESC
Select C: BASIC SETUP and press
the key.
Select C10: TAG NO. and press
the key.
Displays the name of connected
DPharp model, TAG NO. and
diagnostics information. Press the
(OK) key after confirmation.
Press the (SET) key to
display the SET menu panel.
––WELCOME––
BRAIN TERMINAL
ID: BT200
check connection
push ENTER key
UTIL FEED
F0308.EPS
SET
C10:TAG NO.
YOKOGAWA
YOKOGAWA
CODE CAPS CLR ESC
When you have made an entry mistake, return
the cursor using the key, then reenter.
Set the new TAG NO. (FI1-1a).
F OKOGAWA
FIKOGAWA
FI1OGAWA
FI1-GAWA
FI1-1AWA
FI1-1aWA
FI1-1a
Set TAG NO. and press the
key. SET
C10:TAG NO.
YOKOGAWA
FI1-1a _
CODE caps CLR ESC
• Example: Set a Tag No. to FI1-1a
SET
C10:TAG NO.
FIC-1a
FEED NO OK
DATA DIAG PRNT ESC
This is the panel for confirming
set data. The set data items flash.
When all items have been confir-
med, press the
again. (To go back to the setting
panel, press the (NO) key.
SET
C10:TAG NO.
YOKOGAWA
FIC-1a
print off
F2:printer on
PARAM
C10:TAG NO.
FIC-1a
C20:PRES UNIT
kPa
C21:PRES LRV
0.00000 kPa
FEED POFF NO
The DPharp TAG NO. was
overwritten.
Press the (OK) key to
return to the parameter panel.
Press the (NO) key to
return to the setting panel.
F0309.EPS
(2) Calibration Range Setup
a. Setting Calibration Range Unit
(C20: PRES UNIT)
The unit parameter is set at the factory before shipment
if specified at the time of order. Follow the procedure
below to change the unit parameter.
• Example: Change the unit from mmH2O to kPa.
ESC
SET
C20:PRES UNIT
kPa
FEED NO OK
SET
C20:PRES UNIT
mmH2O
< mmWG >
< mmHg >
< Torr >
< kPa > Use the or
key to select kPa.
Press the key twice
to enter the setting.
Press the (OK) key.
F0310.EPS
Note that the Yokogawa default setting for the standard
temperature is 4
ЊC (39.2ЊF). For the units of mmH
2
O,
mmAq, mmWG, inH
2
O, and ftH
2
O, the pressure varies
according to the standard temperature definition. When
a standard temperature of 20
ЊC (68ЊF) is required,
select @20degC (68.0F) at the parameter of D16:H2O
UNIT SEL.
Available pressure units are shown below.
FX0301.EPS
mmH2O
mmAq
mmWG
mmHg
Torr
kPa MPa
mbar
bar
gf/cm2
kgf/cm2
inH2O inHg
ftH2O
psi
atm
Pa
hPa