Staub Electronics SM-CS-ART2-L STRONG - CONTRACTOR SERIES ARTICULATING MOUNT FOR 42 - 63 FLAT PANEL TVS - Manual (Page 2)

ASSEMBLY INSTRUCTIONS
WARNINGS:
• Make sure these instructions are read and thoroughly understood before attempting installation. If you are unsure of any part of the installation
process, contact a professional installer for assistance.
• The wall or mounting surface must be capable of supporting the combined weight of the mount and the display; otherwise the structure must be
reinforced. Installer is responsible for verifying the wall/mounting surface and the anchors used can support the total load of the installation.
• Safety gear and proper tools must be used. Failure to do so can result in property damage and/or serious injury.
• A minimum of two people is required for this installation. Do not attempt to install this mount alone under any circumstance. We highly recom-
mend this product be installed by a qualified professional person.
• Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display. Consult the
owner’s manual for your display for more information.
INSTALLATION
Step 1: Use template to mark mounting
hole locations for flange bolts
Note: Corners fold up to catch debris, if needed.
Step 2: Pre-drilling
For Mounting on a Stud Wall
Pre-drill holes into studs using a 1/4” drill bit.
WARNING:
Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
the screws, greatly reducing their holding strength.
Make sure that mounting screws are anchored into
the center of the studs. The use of a stud finder is
highly recommended.
For Mounting on a Concrete Wall
Pre-drill holes into concrete using 5/16” drill bits.
Insert concrete wall anchors and tap in with hammer,
if necessary.
WARNING:
When installing wall arm assembly on cinder block,
verify first that you have a minimum of 1-3/8” of
concrete thickness to be used for the concrete
anchors. Do not drill into mortar joints! Be sure
to mount in a solid part of the block, generally1”
minimum from the side of the block. Cinder block
must meet ASTM C-90 specifications. It is suggested
that a standard electric drill on slow setting is used
to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a
void or cavity.
Concrete must be 2000 psi density minimum.
Lighter density concrete may not hold con-
crete anchor
.
Make sure that the supporting surface will safely
support the combined load of the equipment and
all attached hardware and components.
Step 3: Mount the Arm Assembly
For Mounting on a Stud Wall or Concrete Wall
Insert flange bolts through the wall plate into the studs
or the wall anchors. When Installing on concrete, 6 bolts
are needed. Insert four through top set of holes; two on
the far holes, and two near the center. Insert the remain-
ing two bolts on the bottom set of holes.
PACKAGE CONTENTS:
SPECIFICATIONS:
• Maximum Load: 150 lbs. (68.04 kg)
• Display Size: 42” to 63”
• Maximum Extension: 30-5/8”
• Wire management
• Pan/Swivel Range: 180°
• Tilt Range: -5° /+ 15°
BOX CONTENTS:
• Wall Arm Assembly (1)
• Adapter Bracket (2)
• Adapter Panel (1)
• Hardware kit (1)
TOOLS REQUIRED:
• Power Drill
• 1/4” & 5/16” Drill Bits
• Level
• 13mm (1/2”) Socket Wrench or Shifter
Drill holes and
insert anchors.
Place wall assembly
arm with plate
over anchors and
secure bolts.
Tighten all
fasteners.
wall plate
CONCRE
TE
WALL
wall anchor
flange bolt
flange bolts
(A) M4 x 15mm Philips
Head Screw (x4)
(D) M8 x 15mm Philips
Head Screw (x4)
(N) M6 x 12mm Philips
Head Screw (x4)
(O) M8 x 15mm Philips
Head Screw (x4)
(P) 36.2 x 36.2 x 2.5mm
Square Washer
(Q) M10 x 70 Concrete
Wall Anchors (x6)
(R) 6 x 13 x 1.2mm
Metal Washer (x4)
(S) Allen Key (x1)
(T) Recessed Hole
Spacer (x4)
(U) Spacer (x4)
Template (x1)
Wire Management
Caps
Wall Arm Assembly (x1)
Adapter Bracket (x2)
Adapter Panel (x1)
(E) M4 x 35mm Philips
Head Screw (x4)
(F) M5 x 35mm Philips
Head Screw (x4)
(G) M6 x 35mm Philips
Head Screw (x4)
(H) M8 x 35mm Philips
Head Screw (x4)
(I) M4 x 45mm Philips
Head Screw (x4)
(K) M6 x 45mm Philips
Head Screw (x4)
(J) M5 x 45mm Philips
Head Screw (x4)
(L) M8 x 45mm Philips
Head Screw (x4)
(M) Flange Bolt (x6)
(B) M5 x 15mm Philips
Head Screw (x4)
(C) M6 x 15mm Philips
Head Screw (x4)
wall plate
concrete
wall
Correct
concrete concrete
plaster/
drywall
plaster/
drywall
Incorrect
Cuta
w
ay
Vie
w CAUTION: This wall mount is
intended for use only with
the maximum weight of 150 lbs
M4 x 20 Philips
Head Screw (x4)
M5 x 20 Philips
Head Screw (x4)
M6 x 20 Philips
Head Screw (x4)
M8 x 20 Philips
Head Screw (x4)
Now Includes: