Staub Electronics DF-SL-100-HC DRAGONFLY - 100 IN. HIGH CONTRAST FILM SCREEN W_BLACK VELVET FRAME (HDTV) - Manual

Mounting the screen onto the wall
Care and cleaning
• Your new screen can be effectively cleaned with a soft cloth
using mild soap and water. DO NOT use harsh detergents,
chemicals, distilled spirits or petro-chemicals to clean the
screen; doing so may result in severe damage to the screen or
the frame coating.
• If the felt covering on the frame gets dusty or covered with
lint, use a household vacuum cleaner with a brush or furniture
cleaning attachment to clean the felt. We do not recommend
using excessive amounts of water on the felt.
A B C D E F
DF-SL-84-MW / HC 84” 41.14'' 73.19'' 47.48'' 79.53'' 47.36''
DF-SL-92-MW / HC 92” 45.08'' 80.2'' 51.42'' 86.54'' 51.3''
DF-SL-100-MW / HC 100” 49.02'' 87.17'' 55.35'' 93.5'' 55.24''
DF-SL-106-MW / HC 106” 51.93'' 92.36'' 58.27'' 98.7'' 58.15''
DF-SL-110-MW / HC 110” 53.9''
95.87'' 60.24'' 102.2'' 60.12''
DF-SL-120-MW / HC 120” 58.82'' 104.57'' 65.16'' 110.9'' 65''
DF-SL-133-MW / HC 133” 65.2'' 116'' 71.54'' 122.24'' 71.38''
Fixed Film Screen with Black Velvet Frame
Assembly
&
Installation
Instructions
4”
4”
Top Bracket
Bottom Bracket
Security Clip
Pre-measured
Tether
• Select an appropriate area to mount the screen. Make sure the
position selected will not interfere with existing features of
your room; wall sockets, switches, etc… these all should be
avoided.
• DO NOT install the screen over an electrical outlet or switch.
Doing so poses a serious fire hazard.
• For homes with stud-wall construction, use stud finder or
carefully measure to determine where the studs are located in
the wall. The screen MUST be mounted to the studs- NEVER
rely on gypsum board, drywall, or thin wall materials to
support the weight of the screen!
• The screen is equipped with a set of pre-measured tethered
mounting brackets. There are security clips in the bottom
bracket. The screen should sit centered on the mounting
bracket when installed.
• Drywall/Stud Installation: Using a stud finder, locate studs in
wall. Hang top bracket first (subtracting 1/2” from top of
screen to mark corner edge of top of bracket) with 5X40mm
Philips head screws and washers directly into studs. Pre-
drilling studs with a 5/32” drill bit is recommended.
• Let the bottom bracket drop and, while pulling tethers taut ,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracket should be used.
• Concrete Installation: Hang top bracket first (subtracting 1/2”
from top of screen to mark corner edge of top of bracket).
Pre-drill 3 holes into concrete with 1/4” concrete bit and insert
concrete anchors. Position top bracket over holes and insert
5X40mm Philips head screws and washers.
• Let the bottom bracket drop and, while pulling tethers taut ,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracket should be used.
• Start by lifting screen frame onto top bracket, letting the
bottom rest against bottom bracket. Carefully lift bottom of
screen onto bottom bracket (Figure A & B). Security clips
will lock bottom of screen in place. Installation is complete.
• To release, simply push in clips and carefully lift bottom of
screen up and away from wall.
Drywall Concrete
B A
E
D
B
A
F
C