Staub Electronics SM-CS-ART1-M STRONG - CONTRACTOR SERIES ARTICULATING MOUNT FOR 26 - 47 FLAT PANEL TVS - Manual

For up to VESA 400x600- Large Displays
a. Insert two M8x12mm (O) screws and two
8mm metal washers (S) into top two holes
of Adapter Plate. Leave approximately 1/4”
of exposed thread (Do NOT tighten fully).
b. Lift the display and hook it over the
mounting head by lowering the exposed
portion of the top screws into the open key
slots of Wall Arm Assembly mounting head.
c. Once in position, attach the bottom two
M8x12mm screws (O) and two 8mm metal
washers (S) and secure the Adapter Plate
to the mounting head using the Allen Key (S)
to tighten down all M8 screws (Figure 11).
ADJUSTMENTS:
Adjust Horizontal Level and Tilt
Tilt Adjustment
a. Loosen Tilt Levers on each side of mount
head (Only enough to allow controlled
adjustment) (See Figure 13).
b. Adjust Tilt
c. Lock Tilt Levers (Tighten)
d. Once Tilt Levers are locked, the position of
the levers can be adjusted, without loosening
or tightening the unit, by pulling the levers
outwards and then repositioning them to a
vertical, less obtrusive positon.
Horizontal Adjustment
a. To adjust the horizontal angle of the display,
first slightly loosen the top two screws on
back side of Wall Arm Assembly mounting
head using Allen Key (T). Then firmly hold
opposite corners of the display and gently
turn it into the desired position. When level,
re-tighten screws to lock in the position
(See Figures 12 & 13).
OTHER FEATURES:
Cable Management
Install cord covers as shown. Be sure to
leave enough slack to allow for movement
of the arms (See Figure 14).
Optional Adhesive Rubber Pads
Included with hardware pack are rubber
pads for cushioning impact of arm against
the wall when retracting mount. Place pads
on opposite side of cable management
covers where possible impact points will
occur (See Figure 15).
SM-CS-ART1-M
Strong™ Contractor Series Universal Single Arm
Articulating Mount for Medium Displays (Black)
PACKAGE CONTENTS:
(A) M4 x 15mm Philips
Head Screw (x4)
(D) M8 x 15mm Philips
Head Screw (x4)
(N) M6 x 12mm Philips
Head Screw (x8)
(O) M8 x 12mm Philips
Head Screw (x4)
(P) 36.2 x 36.2 x 2.5mm
Square Washer
(Q) M10 x 70 Concrete
Wall Anchors (x3)
(R) 6 x 13 x 1.2mm
Metal Washer (x4)
(T) Allen Key (x1)
(U) Recessed Hole
Spacer (x4)
(V) Spacer (x4)
Wall Arm Assembly (x1)
Adapter Bracket (x2)
Adapter Bar (x2)
Adapter Plate (x1)
(E) M4 x 35mm Philips
Head Screw (x4)
(F) M5 x 35mm Philips
Head Screw (x4)
(G) M6 x 35mm Philips
Head Screw (x4)
(H) M8 x 35mm Philips
Head Screw (x4)
(I) M4 x 45mm Philips
Head Screw (x4)
(K) M6 x 45mm Phillips
Head Screw (x4)
(J) M5 x 45mm Philips
Head Screw (x4)
(L) M8 x 45mm Philips
Head Screw (x4)
(M) Flange Bolt (x3)
(B) M5 x 15mm Philips
Head Screw (x4)
(C) M6 x 15mm Philips
Head Screw (x4)
NS
WARNINGS:
• We highly recommend this product be installed by a qualified professional.
• Please do not begin installation until you have thoroughly read and understood these instructions.
• This mount supports display mounting from 26” to 47”, VESA 75X75, 100x100, 200x100, 200x200, up to 600x400
and supports a maximum load of 41kgs (90 lbs).
• Ensure the wall that you plan to use will safely support four times the combined weight of the Mount
and your chosen display.
• Under no circumstances should this product be mounted to metal studs.
• The manufacturer does not accept responsibility for incorrect installation.
SPECIFICATIONS:
• Maximum Load: 90 lbs. (41 kg)
• Display Size: 26” to 47”
• Maximum Extension: 24-3/8”
• Wire management
• Pan/Swivel Range: 180°
• Tilt Range: -5° /+ 15°
BOX CONTENTS:
• Wall Arm Assembly (1)
• Adapter Bracket (2)
• Adapter Panel (1)
• Adapter Bar (2)
• Hardware kit (1)
TOOLS REQUIRED:
• Power Drill
• 5/6” and 1/4” Drill Bit
• Phillips Head Screw Driver
• Level
• 13mm (1/2”) Socket Wrench
+10° /-5°Tilt
±5° Horizontal
Adjustment
(W) Rubber Adhesive
Safety Pads (x4)
Template (x1)
M4 x 20 Philips
Head Screw (x4)
M5 x 20 Philips
Head Screw (x4)
M6 x 20 Philips
Head Screw (x4)
M8 x 20 Philips
Head Screw (x4)
Allen Key (T)
M8x12
Screw Bolt (O)
Horizontal
Adjustment
Screws
Metal
Washer (S)
(S) 8.2 x 16 x 1.5mm
Metal Washer (x4)
Rubber Adhesive
Safety Pads (W)
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and
labor repairs on all components found to be defective in material or workmanship
under normal conditions of use. This warranty shall not apply to products which have
been abused, modified or disassembled. Products to be repaired under this warranty
must be returned to Snap AV or a designated service center with prior notification and
an assigned return authorization number (RA).
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
For Technical Support call 1.866.838.5052
Tilt Lever
(one on
each side)
Lifetime
engineered by
CAUTION:
This wall
mount is intended for use
only with the maximum
weight of 90 lbs
Now Includes: