Staub Electronics SM-ART1-S STRONG - ARTICULATING MOUNT FOR 13 - 27 FLAT PANEL TVS User Manual

Specifications, Box contents warnings, Installation hardware kit

Display Size: 13” to 27”
Maximum Load: 33 lbs (15.0 kg)
Mounting Pattern: VESA 75

75, 100

100, 200

100

Tilt Range: +/- 13.8°
Pan/Swivel Range: 180°
Horizontal Rotation: 360°

cm)

SPECIFICATIONS

Articulating Wall Mount (x1)
Wall Plate (x1)
Instruction Manual (x1)
Hardware Kit (x1)

BOX CONTENTS

WARNINGS

Make sure these instructions are read and
thoroughly understood before attempting
installation. If you are unsure of any part of the
installation process, contact a professional
installer for assistance.

The wall or mounting surface must be capable
of supporting the combined weight of the
mount and the display; otherwise the
structure must be reinforced.

Safety gear and proper tools must be used.
Failure to do so can result in property damage
and/or serious injury.

Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult
the owner‘s manual for your display for more
information

INSTALLATION

HARDWARE KIT

IMPORTANT! For safety reasons, this mount must
be secured to a wood stud. The stud must be
capable of supporting the combined weight of
the mount and the display.

OPERATION AND ADJUSTMENT

Move the wall plate back into position and
secure it using the Wood Screws (A) from the
hardware kit. Do not over-tighten these bolts.

IMPORTANT! For safety reasons, the concrete wall
must be capable of supporting the combined
weight of the mount and the display.

IMPORTANT! Use extra care during this part of
the installation. If possible, avoid placing your
display facedown as it may damage the viewing
surface.

NOTE:
lengths to accommodate a wide variety of display
models. Not all of the hardware in the kit will be
used.

To adjust the tilt angle or rotate your screen,

to hold your mount in position, adjust the
three screws located directly behind the head
of the mount using the S4 Allen Key (G) from
the hardware kit (see illustration). Make sure
you adjust all three screws evenly.

single stud where you want to install your
mount.

Mark both edges of the stud to help identify
the exact center (see illustration).

Place the wall plate over the center of the
marked stud and level it using the integrated
bubble level.

Mark the two holes for securing the mount
and set the wall plate aside.

Drill a pilot hole at each marked location using
an electric or portable drill and 3/16” (5 mm) bit.

Move the wall plate back into position and
secure it using the Wood Screws (A) from the
hardware kit. Do not over-tighten these

screws.

To complete the installation, simply slide the
mount with your display attached into the
wall plate. The plastic tab at the top of the wall
plate will click to indicate that the mount is
secure.

To remove the mount from the wall, push in
on the plastic tab and carefully slide the
mount upwards and out of the wall plate.

For extra security and stability, tighten the set
screw located on the wall plate (see
illustration) using the S3 Allen Key (F) provided
with the hardware kit. Remember to loosen

the set screw before attempting to remove

the mount from the wall.

To use the integrated cable management

on the arms of the mount (see illustration).
Route your cables through the arms and
re-attach the plastic covers to hold them in
place. Make sure to leave enough slack in the
cables so that they are not pulled or pinched
when you move the mount. You may also
route the cables through the hook located at
the bottom of the wall plate.

Swivel adjustments can be made simply by
moving your display into the desired position.
If any of the swivel joints are too tight or
become too loose to hold the mount in place,
they can be adjusted using the S4 Allen Key
(G) provided in your hardware kit (see
illustration).

Part 1A – Installing the Wall Plate

(Drywall) (continued)

Part 1A – Installing the Wall Plate

(Drywall)

Phillips Head Screw Driver

Electric or Portable Drill

3/16” (5 mm) Drill Bit and Stud Finder for
Drywall Installation

5/16” (8 mm) Masonry Bit for Concrete
Installation

TOOLS REQUIRED

UNIVERSAL SINGLE-ARM ARTICULATING

MOUNT FOR SMALL DISPLAYS

SM-ART1-S

Part 1B – Installing the Wall Plate

(Concrete)

Part 1B – Installing the Wall Plate

(Concrete) (continued)

Part 2 – Attaching the Mount to the

Display

Part 3 – Final Assembly

Left edge of stud

Right edge of stud

Center of stud

(D) M4x30 Bolt (x4)

(E) Spacer (x4)

(B) Concrete Anchor (x2)

(G) S4 Allen Key (x1)

Determine the correct bolt to use by
examining the back of your display:

you will use one of the M4x12 Bolts (C)
from the hardware kit.

If the back of your display is curved, has a
protrusion, or if the mounting holes are
recessed, you may need to use one of the
M4x30 Bolts (D) and the Spacers (E).

Attach the mount to the back of your display

sure all screws are secure, but do not
over-tighten.

NOTE: If the holes of the mount do not line
up with the holes on your display, check to
make sure that your display is VESA
compatible. This mount can only be used with
displays that are VESA 75,100, or 200
compatible.

Part 2 – Attaching the Mount to the

Display (continued)

(F) S3 Allen Key (x1)

Place the wall plate against the wall in the
desired location and level it using the
integrated bubble level.

Mark the two holes for securing the mount
and set the wall plate aside.

Drill a 5/16” (8 mm) hole at both marked
locations. Remove any excess dust from the
holes.

Insert a Concrete Anchor (P) into each hole so

hammer can be used to lightly tap the
anchors into place if necessary.

NOTE: If the concrete wall is covered by a
layer of plaster or drywall, the concrete anchor
must pass completely through the layer to rest

Part 3 – Final Assembly (continued)

(A) Wood Screw (x2)

10405 Granite Street, Charlotte, NC 28273

Rev 090622

Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and
labor repairs on all components found to be defective in material or workmanship
under normal conditions of use. This warranty shall not apply to products which

warranty must be returned to SnapAV or a designated service center with prior

INSTRUCTION MANUAL

For Technical support call 866.838.5052

Lifetime

CAUTION: This wall mount is intended for use

only with the maximum weight of 33 lbs