Staub Electronics SM-CEILING-T-L STRONG - LARGE CEILING MOUNT FOR 36-60 FLAT PANEL DISPLAYS - Manual (Page 2)

WARNINGS
• We highly recommend this product be installed by a qualified professional.
• Please do not begin installation until you have thoroughly read and
understood these instructions.
• This mount supports display mounting from 36” to 60”, VESA 200x200 up to
700x500, and supports a maximum load of 175 lbs (79.5 kg).
• Ensure the wall that you plan to use will safely support four times the
combined weight of the mount and your chosen display.
• Under no circumstances should this product be mounted to metal studs.
• The manufacturer does not accept responsibility for incorrect installation.
BOX CONTENTS (T/DT):
• Ceiling Plate (1)
• Ceiling Plate Covers (2)
• Mount Head (1)
• Wall Plate (1/2)
• TV Arms (2/4)
• Hardware kit (1)
• 3’ Fixed Extension Pole (1)
SPECIFICATIONS
• Maximum Load: 175 lbs. (79.5 kg)
• Display Size: 36” to 60”
• Extension: 3’
• Pan/Swivel Range: 360°
• Tilt Range: +0° / -20°
INSTALLATION INSTRUCTIONS
Step 1: Use Ceiling Plate to Mark Mounting Hole Locations
a. The use of a stud finder is highly recommended.
Step 2: Mount the Ceiling Plate
For Mounting on a Wood Joist (Fig 1)
a. Pre-drill four holes into joist using a 3/16” drill bit.
Be sure to drill into the center of the joists.
b. Insert four Lag Screws into holes through
the Ceiling Plate and tighten down.
WARNING: Tighten screws so that the
Ceiling Plate is firmly attached, but
do not over tighten. Over tightening
can damage the screws, greatly
reducing their holding strength.
c. Thread in extension pipe and
tighten set screws provided.
d. Install Ceiling Plate Covers over ends of Ceiling Plate (optional).
For Mounting on a Concrete Ceiling (Fig 2)
a. Pre-drill four holes into concrete using 5/16” Masonry bit. Insert Hex Sleeve anchors
(not supplied) and tap in with hammer (per instructions with wall anchor).
WARNING: When installing Ceiling Plate on cinder block, verify first that
you have a minimum of 1-3/8” of concrete thickness to be used for the
Concrete Wall Anchors (not supplied). Do not drill into mortar joints! Be sure
to mount in a solid part of the block, generally 1”minimum from the side of the
block. Cinder block must meet ASTM C-90 specifications. It is suggested that a
standard electric drill on slow setting is
used to drill the hole instead of a
hammer drill to avoid breaking out
the back of the hole when entering
a void or cavity.
Concrete must be 2000 psi density
minimum. Lighter density concrete
may not hold concrete anchor.
Make sure that the supporting surface will
safely support the combined load of the
equipment and all attached hardware
and components.
b. Remove washer and nut from end of bolt from
all four bolts. Place Ceiling Plate over bolts so they
align with the four holes in Ceiling Plate.
HARDWARE KIT (T/DT)
M4 x 12mm Philips
Head Screw (x4/8)
M6 x 12mm Philips
Head Screw (x4/8)
M8 x 16mm Philips
Head Screw (x4/8)
Allen Wrench 2.5mm,
Security/Non-Security (x2)
Allen Wrench, 4mm (x1)
M4 x 30mm Philips
Head Screw (x4/8)
M5 x 30mm Philips
Head Screw (x4/8)
M6 x 30mm Phillips
Head Screw (x4/8)
M6 x 25mm Phillips
Head Screw (x4/8)
M8 x 25mm Phillips
Head Screw (x4/8)
M8 x 40mm Phillips
Head Screw (x4/8)
Locking Pin (x1/2)
M8 Nylock Nut (x4/8)
M5 x 12mm Philips
Head Screw (x4/8)
M6 x 20mm Philips
Head Screw (x4/8)
M6 (17.8 x 6.5 x 1.5mm)
Metal Washer (x4/8)
M8 (20.5 x 8.5 x 2mm)
Metal Washer (x12/24)
TOOLS REQUIRED
• Power Drill
• 3/16” (5mm) Drill Bit
• 5/16” (8mm) Masonry Bit
• 3/8” & 13mm Socket Head Wrench
• Phillips Head Screw Driver
• 7/16” Socket Head Wrench
Fig 1
Fig 2
#14 x 2.5” Lag Screw (x4)
M4/M5/M6 spacer:
12mm (x4)
M6/M8 Spacer:
17.8mm (x4/8)
M5 x 5mm Set Screw,
Security (x4)
M5 x 5mm Set Screw (x4)
M4/M5/M6 Washers (x4/8)
Concrete anchors not provided. 5/16” x 2-1/2” Red Head® Hex Sleeve Anchors, #50113,
are recommended for concrete or cinder block installation.
CAUTION:
These ceiling mounts are
intended for use only with
the maximum weight of
175 lbs (79.5kg).