Controlled Products Systems Group 1044182 - Manual (Page 22)

L
EARNING OF
N
ORMAL
T
IMES
Normal learning (i.e. without Gatecoders) can be done
in two different ways:
S IMPLE L EARNING ( WITHOUT S LOW D OWN )
Close the gates, enter “B ASIC P ROGRAMMING ”, select the
TIME LEARNING function and press the + push-button
for 1 second the display begins flashing and the
leaves begin the opening movement.
Wait for the leaves to reach the opening positive stop
and then supply an OPEN A command after the
desired motor run time has been reached (by push-
button or radio control) to stop the movement: the
leaves stop and the display stops flashing. One more
command given will close the gate.
The procedure has ended and the gate is ready to
operate.
C OMPLETE L EARNING ( WITH S LOW D OWN )
N OTES :
• If you do not wish to slow the gate operator
(s) down, wait for the gate to reach its
positive stop and supply two (2) consecutive
open commands (within 1 second).
• If only one gate operator (1) is used, you
must go through the entire programming
procedure, as if you were programming for
two gate operators (2). When the operator
has finished opening, supply 5 open
commands until the gate operator begins to
close, and then resume normal operations.
Close the gates, enter “B ASIC P ROGRAMMING ”, select the
TIME LEARNING function and press the + push-button
for more than 3 seconds: the display begins flashing
and leaf 1 begins opening. The following functions
can be commanded by the OPEN A (by push-button
wired to terminals 9 and 14, or radio control):
• When gate operator (1) reaches the position
that you want it to slow down, an open
command must be given to start the slow
down phase.
• When gate operator (1) reaches the positive
stop and the desired motor run time has
been reached, an open command must be
given to shut the motor off. At this point
gate operator (2) will automatically start to
open.
• When gate operator (2) reaches the position
that you want it to slow down, an open
command must be given to start the slow
down phase.
L
EARNING OF
O
PERATING
T
IMES
WARNING: During the learning procedure, the
safety devices are disabled! Therefore, any and all
traffic must be avoided in the path of the gate leaf
(s).
NOTE: Programming must start with the gate(s)
in the closed position.
Opening/closing time is established by the learning
procedure which varies slightly according to whether
you are or are not using Gatecoders.
Pag e 22
M a y, 20 06
4 1 5 L LS Ope ra tor And
4 5 5 D C ontrol Pa ne l I nsta ll a ti on Ma nua l
T
HE
455 D C
ONT
R
OL
P
ANE
L
I
NST
A
LLA
T
ION
I
NS
T
R
U
C
T
IO
N
S
Display Function Default
A SSISTANCE R EQUEST ( COMBINED
WITH NEXT FUNCTION ): If activated,
at the end of countdown (settable
with the next function, i.e. “Cycle pro-
gramming”) it effects 8s of pre-
flashing at every Open pulse (job re-
quest). Can be useful for setting
scheduled maintenance jobs.
Y = Enable
No = Disabled
C YCLE P ROGRAMMING :
For setting count down of system op-
eration cycles. Settable (in thou-
sands) from 0 to 99 thousand cycles.
The displayed value is updated as
cycles proceed. This function can be
used to check use of the board or to
exploit the “Assistance Request” func-
tion
.
E XIT P ROGRAMMING :
Exit from programming and return to
display of inputs status.
ADVANCED PROGRAMMING CONTINUED
A NTI -C RUSHING S ENSITIVITY :
When operating with the gatecoder, it
controls anti-crushing sensitivity.
Y = Low
No = High
E XTRA W ORK T IME :
When operating without a gatecoder
and limit-switch, if reversing occurs,
and if the leaf does not reach its end
contact point, you can activate this
function to increase work time.
Y = A CTIVE
N O = D ISABLED