ClimaCool SHC onDEMAND 30, 50, 70, 85 Manual - Manual (Page 46)

www.climacoolcorp.com
44
Dzdz–”ƒ‹‡”
Before installing the “Y” strainer, be sure its pressure
rating is correct for the system. If the end connections are
threaded or designed for soldering or brazing, be sure the
’‹’‹‰‹••–”ƒ‹‰Š–ƒ†‘–ƒ–ƒƒ‰Ž‡‘”‘ơ•‡–Ǥˆ–Š‡•–”ƒ‹‡”
Šƒ•ƪƒ‰‡†‡†•ǡ„‡•—”‡–Š‡ƪƒ‰‡•‘ˆ–Š‡ ‘‡ –‹‰
piping are square with the pipe so that no undue stress is
’—–‘–Š‡•–”ƒ‹‡”‘”’‹’‹‰™Š‡–‹‰Š–‡‹‰–Š‡ƪƒ‰‡
bolts. Tighten in sequence, crossing to opposites.
‘”ƒš‹—‡ƥ ‹‡ ›ǡƒ†‹ơ‡”‡–‹ƒŽ’”‡••—”‡‰ƒ—‰‡
installed across the inlet and outlet will indicate pressure
loss due to clogging and may be used as a guide to
determine when cleaning is required. Normally, when
†‹ơ‡”‡–‹ƒŽ’”‡••—”‡”‡ƒ Š‡•͙Ǧ͕͔’•‹ǡ–Š‡• ”‡‡—•–„‡
cleaned. If the strainer is equipped with a blow-down valve,
‘’‡ƒ†ƪ—•Š‘—–—–‹Žƒ›•‡†‹‡–‹•”‡‘˜‡†Ǥˆ–Š‡
•–”ƒ‹‡”‹•‘–Ƥ––‡†ˆ‘”„Ž‘™Ǧ†‘™ Ž‡ƒ‹‰ǡȋ•–”ƒ‹‡”—•–
„‡‘ơŽ‹‡Ȍǡ”‡‘˜‡–Š‡ ‘˜‡”‘” ƒ’ƒ† Ž‡ƒ–Š‡• ”‡‡Ǥ
Reinstall the screen in the strainer in the same position
as before and tighten the cover or cap. Replace the
gasket if necessary.
Keeping a spare, clean screen will minimize shut
down time.
Warning: Individuals performing removal and disassembly
should be provided with suitable protection from possibly
hazardous liquids. ‘–‡ǣƒ”‰‡•‹œ‡Dzdz•–”ƒ‹‡”•ƒ”‡
•—’’Ž‹‡†™‹–Š”‡‡ ŠǦ‘• ”‡‡•Ǥ‘”‡‘˜‡–Š‡• ”‡‡ǡ
rotate the screen 45
0 and the Breech-Lok will disengage.
‹‹—͚͔‡•Š• ”‡‡‹•”‡“—‹”‡†Ǥ
Body
Screen
Gasket
Cover Bolts
Typical flanged end "Y" strainer
Cover
NPT tapping for drain plug
(Optional on some models)
Cover Knobs
O-Ring
O-Ring
Body
Gasket
Body
NPT Plug
NPT Plug
Basket
Basket
Cover
Cover Cover Bolts
Basket Strainer
Installation
Before installing the simplex basket strainer, be sure
its pressure rating is correct for the system. If the end
connections are threaded, be sure the piping is straight and
‘–ƒ–ƒƒ‰Ž‡‘”‘ơ•‡–Ǥˆ–Š‡•–”ƒ‹‡”Šƒ•ƪƒ‰‡†‡†•ǡ
„‡•—”‡–Š‡ƪƒ‰‡•‘ˆ–Š‡ ‘‡ –‹‰’‹’‹‰ƒ”‡•“—ƒ”‡
with the pipe so that no undue stresses are put on the
•–”ƒ‹‡”‘”’‹’‹‰™Š‡–‹‰Š–‡‹‰ƪƒ‰‡„‘Ž–•Ǥ‹‰Š–‡
bolts in sequence crossing to opposites.
Maintenance
‘”ƒš‹—‡ƥ ‹‡ ›ǡƒ†‹ơ‡”‡–‹ƒŽ’”‡••—”‡‰ƒ—‰‡
installed across the inlet and outlet will indicate pressure
loss due to clogging and may be used, as a guide, to
determine when cleaning is required. If the strainer is not
set up for backwash cleaning, remove the cover access to
the basket. After cleaning, replace the basket in the same
position as before and tighten the cover. Replace the
gasket or O-ring if necessary. Keeping a spare, clean
basket will minimize shut down time.
Warning: Individuals performing removal and disassembly
should be provided with suitable protection from possibly
hazardous liquids. Knob and clamp type quick opening
covers should not be used for high temperature service.
Consult factory for recommendations. ‘–‡ǣ‹‹—͚͔
‡•Š• ”‡‡‹•”‡“—‹”‡†Ǥ
Basket Strainers should be installed in the position shown in the
illustrations above.
Typical threaded "Y" strainer
Mounting Positions
The cover of the "Y" side should face down
Body
Screen
Gasket
Vertical Horizontal
Cap
(Tapping for NPT
drain plug optional on
some sizes)