Atec Agilent-N9038A - Manual (Page 11)

11
Displayed average noise level (DANL)
(continued)
(Input terminated, sample or average detector, averaging type = Log, 0 dB input attenuation, IF Gain = High, 20 to 30 °C)
RF Input 1; RF Input 2 to 1 GHz; RF Input 2 performance = RF Input 1 performance +11 dB
Specification Typical including NFE 1
Preselector on, preamp off 20 Hz 3
100 Hz 3
1 kHz 3
9 kHz
100 kHz
1 to 3 MHz
3 to 30 MHz
30 to 300 MHz
300 to 600 MHz
600 MHz to 1 GHz
1 to 2 GHz
2 to 2.5 GHz
2.5 to 3 GHz
3 to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 20.0 GHz
20.0 to 26.5 GHz
–92 dBm
–101 dBm
–114 dBm
–118 dBm
–130 dBm
–147 dBm
–150 dBm
–151 dBm
–153 dBm
–151 dBm
–150 dBm
–152 dBm
–151 dBm
–148 dBm
–148 dBm
–147 dBm
–141 dBm
–142 dBm
–135 dBm
–100 dBm 2
–109 dBm 2
–120 dBm 2
–132 dBm
–143 dBm
–158 dBm
–160 dBm
–161 dBm
–164 dBm
–162 dBm
–161 dBm
–164 dBm
–163 dBm
–161 dBm
–159 dBm
–158 dBm
–151 dBm
–152 dBm
–146 dBm
Preselector on, preamp on 1 kHz 3
9 kHz
100 kHz
1 to 2 MHz
2 to 30 MHz
30 to 600 MHz
600 to 800 MHz
800 MHz to 1 GHz
1 to 2 GHz
2 to 2.75 GHz
2.75 to 3.6 GHz
3.5 to 8.4 GHz
8.3 to 13.6 GHz
13.5 to 17.1 GHz
17.0 to 20.0 GHz
20.0 to 26.5 GHz
–119 dBm
–143 dBm
–154 dBm
–166 dBm
–158 dBm
–159 dBm
–157 dBm
–158 dBm
–156 dBm
–160 dBm
–157 dBm
–164 dBm
–162 dBm
–160 dBm
–158 dBm
–155 dBm
–133 dBm 2
–154 dBm
–165 dBm
–178 dBm
–167 dBm
–166 dBm
–166 dBm
–167 dBm
–164 dBm
–168 dBm
–165 dBm
–172 dBm
–173 dBm
–171 dBm
–165 dBm
–162 dBm
1. Typical DANL including NFE = Typical DANL-DANL improvement with NFE.
2. No NFE factor at this frequency.
3. Specified for instruments with prefixes MY/SG5213 or greater. Nominal for instruments with earlier prefixes.