Extron Electronics PVS 405D User Guide - Manual (Page 33)

Command ASCII Command
(host to switcher)
Response
(switcher to host)
Additional Description
Special functions
Set lineout mode
Set lineout to
variable 55*1# LineOut*X] Set lineout port mode to variable (X=1,
default).
Set lineout to fixed 55*2# LineOut*X] Set lineout port mode to fixed (X=2).
View lineout mode 55# LineOut*X] View lineout port mode (X= 1 or 2).
Set audio output mode
Set audio output
mode to dual mono 18*1# PreAmpMod*X] Set audio output mode to dual mono
(X=1, default).
Set audio output to
fixed 18*2# PreAmpMod*X] Set audio output mode to stereo (X=2).
View audio output
mode 18# PreAmpMod*X] View audio output mode (X= 1 or 2).
Paging sensor hold time
Set paging sensor
hold time 75*x# PageDly*X] Set paging hold time (x = 0 to 8
seconds) in 1 second steps: default = 3
(enable), 0 = 0 seconds (disabled), 1 =
1.0 second, 2 = 2.0 seconds...8 = 8.0
seconds.
View paging sensor
hold time 75# PageDly*X] View paging hold time (where x = 0 to 8)
Paging sensor sensitivity
Set paging sensor
sensitivity 83*x# PageSen*X] Set paging sensitivity (where x = 0 ‑ 100,
50 = default).
View paging sensor
sensitivity 83# PageSen*X] View paging sensitivity (where x = 0 to
100)
Picture adjustment (PVT SW HDMI RGB D inputs 2 and 4 only)
Set pixel phase value E X3^ *X3&PHAS} PhasX3^*X3&] Set pixel phase X3& for X3^ .
Increment pixel
phase value E X3^ +PHAS} PhasX3^*X3&] Increase pixel phase to X3& for X3^ .
Decrement pixel
phase value E X3^ -PHAS} PhasX3^*X3&] Decrease pixel phase to X3& for X3^ .
View pixel phase
value E X3^ PHAS} X3&] View pixel phase X3& for X3^ .
Verbose response PhasX3^*X3&]
Set total pixel value E X3^ *X2@TPIX} TpixX3^*X2@] Set total pixel X2@ for X3^ .
Increment total pixel
value E X3^ +TPIX} TpixX3^*X2@] Increase total pixel to X2@ for X3^ .
Decrement total pixel
value E X3^ -TPIX} TpixX3^*X2@] Decrease total pixel to X2@ for X3^ .
View total pixel value E X3^ TPIX} X2@] View total pixel X2@ for X3^ .
Verbose response TpixX3^*X2@]
Set horizontal start
value E X3^ *X3*HSRT} HsrtX3^*X3*] Set horizontal start at X3* for X3^ .
Increment horizontal
start value E X3^ +HSRT} HsrtX3^*X3*] Increase horizontal start to X3* for X3^ .
NOTE:
X2@ = Total pixels — ±255 of the default value (depends on input rate)
X3^ = PVT SW HDMI RGB D inputs 2 and 4 only
2 = input 2
4 = input 4
X3&
= Pixel phase ‑ 0‑63 (32 = default)
X3* = Horizontal start ‑ 0‑255 (128 = default)
PVS 405D • SIS Communication and Control 27