Mounting the scs 300 through a desk, Mounting the scs 300 through a desk -5, Mounting the scs 300 through a desk desk – Extron Electronics SCS 300 User Guide User Manual
Page 12
2-5
SCS 300 • Installation, Connection, and Settings
Mounting the SCS 300 through a desk
desk
To mount the SCS 300 through a desk or table using the through
desk mounting kit (Extron part # 70-077-02, MBD 129), do the
following:
1.
Attach the mounting brackets to the SCS 300 using four
machine screws and washers supplied with the mounting
kit, as shown in figure 2-4.
Figure 2-4 — Attaching the through desk brackets
2.
Holding the device up against the underside of the surface
to which you are mounting, mark the four screw holes.
3
.
Drill four pilot holes, each 3/32" (2 mm) in diameter by
1/4" (6.4 mm) deep, where marked on the template.
4.
Using the four supplied wood screws, attach the brackets
to the mounting surface (see figure 2-4).
5
.
When the SCS 300 is mounted, continue the installation by
connecting the input, output, and power cables.
- AVTrac Corner Cut Solution (2 pages)
- AVTrac Demonstration Kit (2 pages)
- AVTRac End Ramp and Cable Pass-Through Kits (1 page)
- AVTrac Extension Kit (15 pages)
- 1U and 2U Rack Plate (1 page)
- Under-Desk Mounting Bracket (1 page)
- AAP Wiring Guide 68-1054-01 (1 page)
- AAP Wiring Guide 68-1052-01 (1 page)
- AAP Wiring Guide (XLR connectors) (1 page)
- AAP 314 (1 page)
- AAP 301 (1 page)
- AAP Wiring Guide 68-1055-01 (1 page)
- AAP Wiring Guide 68-1058-01 (1 page)
- AAP Wiring Guide 68-1059-01 (1 page)
- AAP-MAAP Rev. A (1 page)
- AAP-MAAP Rev. D (1 page)
- MD Floor Box AAP Bracket Kit AAP 100 MD (1 page)
- AC 100 Power Module Series (1 page)
- AAP 103 Extron Ackerman AKM UK Faceplate Kit (1 page)
- ACMP 100 (2 pages)
- Active Audio AAP (1 page)
- AKM UK Series (4 pages)
- Audio AAP Wiring Guide (1 page)
- Audio Connector Rev. A (2 pages)
- Audio Connector Rev. G (1 page)
- AVTrac Extra Channel Kit (2 pages)
- AVTrac Raceway Transition (2 pages)
- AVTrac Retrofit Transition Adapter (2 pages)
- AVTrac Trim Ring-Rough-in Adapter (2 pages)
- AVTrac Above Floor (1 page)
- BB 1 (2 pages)
- BB 1000M (2 pages)
- BB 700M (2 pages)
- BB 710M (2 pages)
- Blank Rack Panel (1 page)
- BNC to 15-Pin HD (1 page)
- BNC-5 RC Termination (1 page)
- Cable Cubby 1200 (6 pages)
- Cable Cubby 200 (18 pages)
- Cable Cubby 300C (27 pages)
- Cable Cubby 500 (6 pages)
- Flexible Conduit Kit (2 pages)
- Cable Cubby Lid and Trim Ring Replacement Kit (for 300C, 300S, 600, 800) (1 page)
- Cable Cubby Setup Guide (4 pages)
- Cable Cubby Single Space AAP Bracket Kit (1 page)