Extron Electronics IN31608 - Manual (Page 19)

16
IN31608 OPERATION MANUAL - REV 1.6 1/4/01

2001 - INLINE, Inc.
COMMAND DESCRIPTION RESPONSE
PTgOooIii
(Matrix Mode) Execute a switch in Matrix Mode. Connect Output mm to Input nn for Group g.
See CNF Command for reference.
g: Group #, a 1 byte ASCII code, 1 <= g <= 3.
ii: Input #, a 2 byte ASCII code, 00 <= ii <= 16.
If nn = 00, no input is selected, resulting in a blank output.
oo: Output #, a 2 byte ASCII code, 00 <= oo <= 8.
Example: [PT 1 O 04 I 02] (spaces added for clarity)
Connect Output #4 to Input #2 for the boards in Group 1.
[OK]
RGBx.x Set RGB delay to x.x seconds. x.x: ranges from 0.0 to 6.0 in 0.1 second
intervals.
Example: [RGB3.7] Set RGB delay to 3.7 seconds. [OK]
SAVExx
(Matrix Mode) Save current configuration to SETUPxx
xx: 2 byte ASCII code, 01 <= xx <= 16.
Example: [SAVE16] Set current configuration to Setup Memory 16.
Note: See [CALLxx] [OK]
STAT0 General status request See examples on pages 15 & 16
STAT1 Video array status request See examples on pages 15 & 16
STAT2 Sync array status request See examples on pages 15 & 16
STAT3 Audio array status request See examples on pages 15 & 16
STAT4 Audio input volume array status request See examples on pages 15 & 16
STAT5 Audio output volume array status request See examples on pages 15 & 16
STAT6 Audio mute array status request See examples on pages 15 & 16
STAT7
(Direct Mode) Direct Mode switch matrix request See examples on pages 15 & 16
STAT8 Projector Port status request See examples on pages 15 & 16
STAT9 Serial Command Port status request See examples on pages 15 & 16
SW (Matrix Mode) Execute all switch connections as defined by the L command. [OK]
VIS0 Disable genlock operation / vertical interval switching [OK]
VIS1 Enable genlock operation / vertical interval switching [OK]
VOLo+ Increment volume for output o, 1 <= o <= 8. In Direct Mode the [VOLo+]
command controls all outputs simultaneously regardless of the ‘o’ channel
selection.
Example: [VOL3+]
In Matrix Mode increment volume for output 3 by one to a maximum
value of 255. In Direct Mode increment volume for all outputs by one to
a maximum value of 255.
Note: see [MDVOL0] & [MDVOL1] [OK]
VOLo- Decrement volume for output o, 1 <= o <= 8. In Direct Mode the [VOLo-]
command controls all outputs simultaneously regardless of the ‘o’ channel
selection.
Example: [VOL6-]
In Matrix Mode decrement volume for output 6 by one to a minimum
value of 0. In Direct Mode decrement volume for all outputs by one to a
minimum value of 0.
Note: see [MDVOL0] & [MDVOL1] [OK]
VOLoxxx Set the output volume for both left and right channels of output ‘o’ to value ‘xxx’.
1 <= o <= 8; 000 <= xxx <= 255 decimal.
In Direct Mode the [VOLoxxx] command controls all outputs simultaneously
regardless of the ‘o’ channel selection.
Example: [VOL6255]
In Matrix Mode set volume for output 6 to a value of 255. In Direct
Mode set volume for all outputs to a value of 255.
Note: see [MDVOL0] & [MDVOL1]
[OK]