Powersolve JB800 Series - Manual (Page 2)

Powersolve Electronics Ltd. 8A Arnhem Road, Newbury, RG14 5RU. England
Tel: 01635 521858 Fax: 01635 523771 Email: [email protected]
www.powersolve.co.uk
AC-DC Converter
Output Voltage and Current Ratings
MODEL INPUT RATING OUTPUT VOLTAGE MAX OUTPUT REGULATION RIPPLE & POWER
Preset Range CURRENT NOISE Max.
JB500X-3V3(I) 90-264Vac 8A 3.3VDC 2 - 3.3V 80A ±1% 75mV 264W
JB500X-5(I) 90-264Vac 8A 5VDC 5 - 6V 80A ±1% 75mV 400W
JB500X-12(I) 90-264Vac 8A 12VDC 12 - 15V 41.67A ±1% ±1% 500W
JB500X-18(I) 90-264Vac 8A 18VDC 16 - 21V 31.25A ±1% ±1% 500W
JB500X-24(I) 90-264Vac 8A 24VDC 22 - 30V 22.73A ±1% ±1% 500W
JB500X-36(I) 90-264Vac 8A 36VDC 31 - 47V 16.13A ±1% ±1% 500W
JB500X-48(I) 90-264Vac 8A 48VDC 48 - 56V 10.42A ±1% ±1% 500W
JB600X-12(I) 90-264Vac 10A 12VDC 12 - 14V 50A ±1% ±1% 600W
JB600X-15(I) 90-264Vac 10A 15VDC 15 - 19V 40A ±1% ±1% 600W
JB600X-24(I) 90-264Vac 10A 24VDC 20 - 26V 30A ±1% ±1% 600W
JB600X-36(I) 90-264Vac 10A 36VDC 27 - 36V 22.22A ±1% ±1% 600W
JB600X-40(I) 90-264Vac 10A 40VDC 37 - 47V 16.22A ±1% ±1% 600W
JB600X-48(I) 90-264Vac 10A 48VDC 48 - 60V 12.5A ±1% ±1% 600W
JB750X-12(I) 90-264Vac 12A 12VDC 12 - 14V 62.5A ±1% ±1% 750W
JB750X-15(I) 90-264Vac 12A 15VDC 15 -19V 50A ±1% ±1% 750W
JB800X-24(I) 90-264Vac 12A 24VDC 20 - 26V 40A ±1% ±1% 800W
JB800X-36(I) 90-264Vac 12A 36VDC 27 - 36V 29.63A ±1% ±1% 800W
JB800X-40(I) 90-264Vac 12A 40VDC 37 - 47V 21.62A ±1% ±1% 800W
JB800X-48(I) 90-264Vac 12A 48VDC 48 - 60V 16.67A ±1% ±1% 800W
Connection Details
Notes:
• X in the part number can be ‘E’ (enclosed with end fan), ‘F’ (enclosed with top fan), ‘U’ (U chassis with optional cover)
• (I) denotes models with forced current sharing option (internal OR-ing diode)
• All voltages shown in output voltage range can be set and still carry agency certifications
• Standard models come with output voltage preset
• U chassis versions need external 30CFM forced air cooling to achieve maximum output power
• Ripple & noise are measured from 10KHz to 20MHz bandwidth with an 0.1µF ceramic and 22µF electrolytic capacitor across the output
• Provides peak power up to 900W for 500µS for all models. For longer duration contact sales office
• 1% minimum load required to maintain regulation
• Cover is optional for U-chassis type
• Output is fully isolated
AC Input Connector (CN1):
E Type: IEC320 or equivalent Snap-in mounting type or DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin)
U & F Type: Mating Molex Part No. 09-91-0700 or equivalent (7 pins, 5 used) or Howder Terminal Block Part No. HD-121-8P
Crimps: Molex Part No. 2578
Output Connector (CN2):
Mating Molex Part No. 09-91-2000 (20 pin) or Howder Terminal Block Part No. HD-121-8P (8 pin)
Crimps: Molex Part No. 2578
Output Pin Assignment:
Molex: VO+ (Pins 1-10), VO- (Pins 11-20), Howder: VO+ (Pins 1-4), VO- (Pins 5-8)
Logic Signal Connectors (CN3):
Mating JST XHP-7 or equivalent (CHYAO SHIUNN JS-2001-07)
Crimps: JST SXH-001T-P0.6 (CHYAO SHIUNN JS-2001-TB)
Fan Drive: 12VDC/500mA.
Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02)
Crimps: JST SXH-001T-P0.6 (CHYAO SHIUNN JS-2001-TB)
Mounting Inserts:
6-32 and M4, 4 places each with maximum penetration 0.2 inch on bottom side and 0.25 inch on both sides