Veris Industries H922030A Install - Manual

6%2)3 CURRENT MONITORING INSTALLATION GUIDE
Z204089-0C PAGE 1 ©2009 Veris Industries USA 800.354.8556 or 503.598.4564 / [email protected] 03095
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Split-Core Self-Powered Current Transducer,
30, 60, or 120 Amp, 0-5VDC Output
Installer’s Specifications
Amperage Range 0-30/60/120 Amps (fixed)
Sensor Power Induced from monitored conductor
Insulation Class 600VAC RMS
Frequency 50/60Hz
Temperature Range -15° to 60°C (5° to 140°F)
Humidity Range 10-90% RH non-condensing
Accuracy ±2% F.S. from 10% to 100% of selected range
Response Time less than 2 sec
Safety IEC 61010-1:2001 CAT III
For CE compliance, conductor shall be insulated according to IEC 61010-1:2001, Installation
Category III or equivalent.
PRoduct design provides for basic insulation only.
)";"3%0'&-&$53*$4)0$,
&91-04*0/
03"3$'-"4)
t 'PMMPXTBGFFMFDUSJDBMXPSLQSBDUJDFT 4FF/'1"&JOUIF64"
PSBQQMJDBCMFMPDBMDPEFT
t 5IJTFRVJQNFOUNVTUPOMZCFJOTUBMMFEBOETFSWJDFECZRVBMJmFEFMFDUSJDBMQFSTPOOFM
t 3FBE
VOEFSTUBOEBOEGPMMPXUIFJOTUSVDUJPOTCFGPSFJOTUBMMJOHUIJTQSPEVDU
t 5VSOPõBMMQPXFSTVQQMZJOHFRVJQNFOUCFGPSFXPSLJOHPOPSJOTJEFUIFFRVJQNFOU
t 6TFBQSPQFSMZSBUFEWPMUBHFTFOTJOHEFWJDFUPDPOmSNQPXFSJTPõ
%0/05%&1&/%0/5)*4130%6$5'0370-5"(&*/%*$"5*0/
t 0OMZJOTUBMMUIJTQSPEVDUPOJOTVMBUFEDPOEVDUPST
'BJMVSFUPGPMMPXUIFTFJOTUSVDUJPOTXJMMSFTVMUJOEFBUIPSTFSJPVTJOKVSZ
%"/(&3
Wiring ExamplE
H922xxxA 922xxxA
DimEnsions
/05*$&
t 5IJTQSPEVDUJTOPUJOUFOEFEGPSMJGFPSTBGFUZBQQMJDBUJPOT
t %POPUJOTUBMMUIJTQSPEVDUJOIB[BSEPVTPSDMBTTJmFEMPDBUJPOT
t 5IFJOTUBMMFSJTSFTQPOTJCMFGPSDPOGPSNBODFUPBMMBQQMJDBCMFDPEFT
t .PVOUUIJTQSPEVDUJOTJEFBTVJUBCMFmSFBOEFMFDUSJDBMFODMPTVSF
quick install
Disconnect and lock out power to the conductor being monitored. 1.
Install the removable mounting bracket to the back of the enclosure. 2.
Run the conductor through the current sensor window, and close the sensor until 3.
the clip snaps shut. For monitoring currents above or below the device’s range, see
the Notes section on page 2.
Connect the 0-5VDC self-powered output to the analog input of the control panel. 4.
Scale the control panel for 0-5VDC input. 5.
Fan or Pump
CONTROLLER
VERIS INDUSTRIES Portland, Oregon 97223 1-800-354-8556
CONTACTOR
MOTOR
Insulated Conductor
COMM
0-5 VDC
+
-