American Magnetics 12200PS DC Power Supply (CE-Marked) - Manual (Page 8)

OPERATING MANUAL ILLUSTRATIONS AND TABLES
Release 1.0 (98/07) v
LIST OF ILLUSTRATIONS
Figure 1.3-1 Typical Input Current Characteristics......................................................................................1-4
Figure 1.3-2 Dimensional Drawings ............................................................................................................1-6
Figure 2.3-1 Power Supply Front Panel .......................................................................................................2-2
Figure 2.3-2 Power Supply Rear Panel ........................................................................................................2-3
Figure 2.3-3 Shipping or Storage Carton Label ...........................................................................................2-4
Figure 2.5-1 AC Input Label and Strain Relief ............................................................................................2-7
Figure 2.7-1 Maximum Load Wire Length for 1V Line Drop .....................................................................2-11
Figure 2.7-2 Output Strain Relief and Bus Bar Cover .................................................................................2-12
Figure 2.7-3 Typical Load Connection Hardware........................................................................................2-13
Figure 2.7-4 Output Voltage Connector.......................................................................................................2-14
Figure 2.7-5 Single Load with Local Sensing (Default)...............................................................................2-15
Figure 2.7-6 Single Load with Remote Sensing...........................................................................................2-15
Figure 2.7-7 Multiple Loads with Local Sensing .........................................................................................2-16
Figure 2.7-8 Multiple Loads with Remote Sensing......................................................................................2-16
Figure 2.8-1 J10 Sense Connector ...............................................................................................................2-17
Figure 2.8-2 Connecting Remote Sense Lines .............................................................................................2-19
Figure 3.2-1 Operating Modes .....................................................................................................................3-1
Figure 3.5-1 Series Operation of Multiple Supplies.....................................................................................3-6
Figure 3.5-2 Parallel Operation of Multiple Supplies ..................................................................................3-7
Figure 3.5-3 Split Supply Operation of Multiple Supplies (Two Positive Voltages) ...................................3-8
Figure 3.5-4 Split Supply Operation of Multiple Supplies (Positive-negative Supply) ...............................3-9
Figure 4.2-1 Programming and Monitoring SW1 Switch ............................................................................4 -1
Figure 4.2-2 Programming and Monitoring J2 Connector ...........................................................................4-2
Figure 4.3-1 Connecting Programming Sources to J2 Connector ................................................................4-6
Figure 5.2-1 Programming and Monitoring Calibration Locations ..............................................................5-2
LIST OF TABLES
Table 1.1-1 Available Voltage and Current Ranges.....................................................................................1-1
Table 1.3-1 Specifications for 7.5V to 60V Models ....................................................................................1-2
Table 1.3-2 Specifications for 100V to 600V Models .................................................................................1-3
Table 2.2-1 Basic Setup Procedure..............................................................................................................2-1
Table 2.5-1 AC Input Voltage Range and Frequency ..................................................................................2-6
Table 2.5-2 AC Wire Specification..............................................................................................................2-6
Table 2.5-3 AC Input Connector Terminals and Connections .....................................................................2-7
Table 2.7-1 Current Carrying Capacity for Load Wiring.............................................................................2-10
Table 2.8-1 Rear Panel J10 Sense Connector Terminals and Functions ......................................................2-17
Table 3.2-1 Shipped Configuration (Local Control Mode)..........................................................................3-2
Table 3.4-1 Switch Settings for TTL Shutdown Circuit Logic ....................................................................3-5
Table 3.6-1 Switch Settings for Over Temperature Recovery Options ........................................................3-9
Table 3.7-1 User Diagnostics.......................................................................................................................3-11
Table 4.2-1 Rear Panel SW1 Switch Assignments (Factory Defaults Underlined)......................................4-2
Table 4.2-2 Rear Panel J2 Connector Terminals and Functions ..................................................................4-3
Table 4.3-1 Remote Programming Options .................................................................................................4-4
Table 4.3-2 Power Supply Settings for Different Programming Sources.....................................................4-5
Table 4.4-1 Power Supply Settings for Remote Monitoring of Readback Signals.......................................4-6
Table 4.5-1 Isolated (ISOL) Programming Interface Specifications............................................................4-7
Table 5.2-1 Current Carrying Capacity for Wiring ......................................................................................5-1