Roland MIDI Implementation DP990F - Manual (Page 29)

29
● 0175: Telephone
No Parameter Value Description
1 Voice Quality #1 0-15 0-15
Audio quality of the telephone
voice
2 Treble 0-30 -15 - +15 dB Bandwidth of the telephone voice
3 Balance #2 0-100
D100:0 -
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
4 Level 0-127 0-127 Output level
● 0156: Gate Reverb
This is a special type of reverb in which the reverberant sound is cut off before
its natural length.
No Parameter Value Description
1 Type #1 0-3
Normal,
Reverse,
Sweep1,
Sweep2
Type of reverb
Normal: conventional gated
reverb
Reverse: backwards reverb
Sweep1: the reverberant sound
moves from right to left
Sweep2: the reverberant sound
moves from left to right
2 Pre Delay 0-125 0.0-100.0 ms
Adjusts the delay time from the
direct sound until the reverb
sound is heard.
3 Gate Time 0-99 5-500 ms
Adjusts the time from when the
reverb is heard until it disappears.
4 Low Gain 0-30 -15 - +15 dB Gain of the low range
5 High Gain 0-30 -15 - +15 dB Gain of the high range
6 Balance #2 0-100
D100:0W -
D0:100W
Volume balance between the direct
sound (D) and the reverb sound
(W)
7 Level 0-127 0-127 Output Level
● 0200: Overdrive→Chorus
This effect connects an overdrive and a chorus in series.
No Parameter Value Description
1 Overdrive Drive 0-127 0-127
Degree of distortion Also changes
the volume.
2 Overdrive Pan 0-127 L64 - 63R
Stereo location of the overdrive
sound
3 Chorus Pre Delay 0-125 0.0-100.0 ms
Adjusts the delay time from the
direct sound until the chorus
sound is heard.
4 Chorus Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
5 Chorus Rate #1 1-127 0.05 - 10.00 Hz Frequency of modulation (Hz)
6 Chorus Rate 0-21 note Frequency of modulation (note)
7 Chorus Depth 0-127 0-127 Depth of modulation
8 Chorus Balance #2 0-100
D100:0W -
D0:100W
Adjusts the volume balance
between the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
9 Level 0-127 0-127 Output Level
● 0201: Overdrive→Flanger
This effect connects an overdrive and a flanger in series.
No Parameter Value Description
1 Overdrive Drive 0-127 0-127
Degree of distortion Also changes
the volume.
2 Overdrive Pan 0-127 L64 - 63R
Stereo location of the overdrive
sound
3 Flanger Pre Delay 0-125 0.0-100.0 ms
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
4 Flanger Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
5 Flanger Rate #1 1-127 0.05-10.00 Hz Frequency of modulation (Hz)
6 Flanger Rate 0-21 note Frequency of modulation (note)
7 Flanger Depth 0-127 0-127 Depth of modulation
8 Flanger Feedback 0-98 -98 - +98%
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
9 Flanger Balance #2 0-100
D100:0W -
D0:100W
Adjusts the volume balance
between the sound that is sent
through the flanger (W) and the
sound that is not sent through the
flanger (D).
10 Level 0-127 0-127 Output Level
● 0202: Overdrive→Delay
This effect connects an overdrive and a delay in series.
No Parameter Value Description
1 Overdrive Drive #1 0-127 0-127
Degree of distortion Also changes
the volume.
2 Overdrive Pan 0-127 L64 - 63R
Stereo location of the overdrive
sound
3 Delay Mode 0-1 ms, note
When this is set to “note,” the
effect is synchronized with the
tempo.
4 Delay Time 0-127 0 - 2540 ms
Adjusts the delay time from the
direct sound until the delay sound
is heard. (Hz)
5 Delay Time 0-21 note
Adjusts the delay time from the
direct sound until the delay sound
is heard. (note)
6 Delay Feedback 49-89 0 - +80%
Adjusts the proportion of the delay
sound that is fed back into the
effect.
7 Delay HF Damp 0-17
200-8000 Hz,
Bypass
Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the
high frequencies, set this
parameter to Bypass.
8 Delay Balance #2 0-100
D100:0W -
D0:100W
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D).
9 Level 0-127 0-127 Output Level
● 0203: Distortion→Chorus
The parameters are essentially the same as in “Overdrive→Chorus,” with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan
● 0204: Distortion→Flanger
The parameters are essentially the same as in “Overdrive→Flanger,” with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan
● 0205: Distortion→Delay
The parameters are essentially the same as in “Overdrive→Delay,” with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan