Roland MIDI Implementation DP990F - Manual (Page 25)

25
● 012d: Rotary2
This type provides modified response for the rotary speaker, with the low end
boosted further.
This effect is a descendant of the Roland VK Series’ built-in rotary speaker.
No Parameter Value Description
1 Speed #1 0-1 Slow, Fast
Rotational speed of the rotating
speaker
2 Brake #2 0-1 Off, On
Switches the rotation of the rotary
speaker. When this is turned on, the
rotation will gradually stop. When it
is turned off, the rotation will
gradually resume.
3 Woofer Slow Speed 1-127 0.05-10.00 Hz
Low-speed rotation speed of the
woofer
4 Woofer Fast Speed 1-127 0.05-10.00 Hz
High-speed rotation speed of the
woofer
5 Woofer Trans Up 0-127 0-127
Adjusts the rate at which the woofer
rotation speeds up when the
rotation is switched from Slow to
Fast.
6 Woofer Trans Down 0-127 0-127
Adjusts the rate at which the woofer
rotation speeds up when the
rotation is switched from Fast to
Slow.
7 Woofer Level 0-127 0-127 Volume of the woofer
8 Tweeter Slow Speed 1-127 0.05-10.00 Hz
9 Tweeter Fast Speed 1-127 0.05-10.00 Hz
10 Tweeter Trans Up 0-127 0-127
11 Tweeter Trans Down 0-127 0-127
12 Tweeter Level 0-127 0-127
Settings of the tweeter The
parameters are the same as for the
woofer.
13 Spread 0-10 0-10
Sets the rotary speaker stereo
image.
The higher the value set, the wider
the sound is spread out.
14 Low Gain 0-30 -15 - +15 dB Gain of the low range
15 High Gain 0-30 -15 - +15 dB Gain of the high range
16 Level 0-127 0-127 Output Level
● 0300: Rotary Multi
This is an effect combining the VK series internal effect with an organ effect
with the same features.
It comprises vibrato/chorus, overdrive, and rotary effects.
No Parameter Value Description
1 Vib/Cho Switch 0-1 Off, On
Switches the vibrato and chorus
effects
Vibrato and chorus effect types
V-1, V-2, V-3: Adds a wavering
(vibrato) that is created by
changes in the pitch.
The effect deepens as the value is
increased
2 Vib/Cho Type 0-5
V-1, V-2, V-3,
C-1, C-2, C-3
C-1, C-2, C-3: Adds a fullness and
breadth (chorus) to the sound.The
effect deepens as the value is
increased.
3 Vib/Cho Vintage 0-2 ‘50, ‘60, ‘70
This reproduces the subtle
differences in the vibrato and
chorus effects in organs built in
different years.
4 Vib/Cho Level 0-127 0-127 Vibrato/chorus effect volume
5 OD Switch 0-1 Off, On Switches the overdrive effect
6 OD Drive #2 0-127 0-127 Amount of distortion
7 OD Level 0-127 0-127 Overdrive effect volume
8 Rotary Switch 0-1 Off, On Switches the rotary effect
9 Rotary Speed #1 0-1 Slow, Fast
Low- and high-frequency rotation
speeds (Rate) Slow: (Slow Rate)
Fast: (Fast Rate)
10 R-Wf Slow Sp 1-127 0.05-10.00 Hz
Rate with low-frequency rotor set to
Slow rate
11 R-Wf Fast Sp 1-127 0.05-10.00 Hz
Rate with low-frequency rotor set to
Fast rate
12 R-Wf Accel 0-15 0-15
Speed at which the low-frequency
rotor’s rotation rate changes when
the rotation speed is switched
13 R-Wf Level 0-127 0-127 Low-frequency rotor volume
14 R-Tw Slow Sp 1-127 0.05-10.00 Hz
15 R-Tw Fast Sp 1-127 0.05-10.00 Hz
16 R-Tw Accel 0-15 0-15
17 R-Tw Level 0-127 0-127
High-frequency rotor setting This
parameter is the same as that for
the low-frequency rotor.
18 Rotary Separat 0-127 0-127 Amount of breadth in the sound
19 Rotary Level 0-127 0-127 Output volume
● 015b: Stereo Delay1
This is a stereo delay.
No Parameter Value Description
1 Delay Left Mode 0-1 ms, note
When this is set to “note,” the
effect is synchronized with the
tempo.
2 Delay Left 0-127 0-1270 ms
Adjusts the time until the delay
sound is heard. (Hz)
3 Delay Left 0-21 note
Adjusts the time until the delay
sound is heard. (note)
4 Delay Right Mode 0-1 ms, note
When this is set to “note,” the
effect is synchronized with the
tempo.
5 Delay Right 0-127 0-1270 ms
Adjusts the time until the delay
sound is heard. (Hz)
6 Delay Right 0-21 note
Adjusts the time until the delay
sound is heard. (note)
7 Phase Left 0-1
8 Phase Right 0-1
Normal,
Inverse
Phase of the delay sound
9 Feedback Mode 0-1 Normal, Cross
Selects the way in which delay
sound is fed back into the effect.
(See the figures above.)
10 Feedback #1 49-89 0 - +80%
Adjusts the amount of the delay
sound that’s fed back into the
effect.
11 HF Damp 0-17
200-8000 Hz,
Bypass
Adjusts the frequency above which
sound fed back to the effect is
filtered out. If you don’t want to
filter out any high frequencies, set
this parameter to Bypass.
12 Low Gain 0-30 -15 - +15 dB Gain of the low frequency range
13 High Gain 0-30 -15 - +15 dB Gain of the high frequency range
14 Balance #2 0-100
D100:0W -
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
15 Level 0-127 0-127 Output level