Roland MIDI Implementation DP990F - Manual (Page 21)

21
● 0127: 3D Flanger
This applies a 3D effect to the flanger sound. The flanger sound will be
positioned 90 degrees left and 90 degrees right.
No Parameter Value Description
1 Filter Type 0-2 Off, Lpf, Hpf
Type of filter
Off: No filter is used
Lpf: Cuts the frequency range
above the Cutoff Freq
Hpf: Cuts the frequency range
below the Cutoff Freq
2 Cutoff Freq 0-16 200-8000 Hz Basic frequency of the filter
3 Pre Delay 0-125 0.0-100.0 ms
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
4 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
5 Rate #1 1-127 0.05-10.00 Hz Frequency of modulation (Hz)
6 Rate 0-21 note Frequency of modulation (note)
7 Depth #2 0-127 0-127 Depth of modulation
8 Phase 0-90 0-180 deg Spatial spread of the sound
9 Feedback 0-98 -98.98
Adjusts the proportion of the
flanger sound that is fed back into
the effect.
Negative (-) settings will invert the
phase.
10 Output Mode 0-1
Speaker,
Phones
Adjusts the method that will be
used to hear the sound that is
output to the OUTPUT jacks. The
optimal 3D effect will be achieved
if you select Speaker when using
speakers, or Phones when
using headphones.
11 Low Gain 0-30 -15 - +15 dB Gain of the low range
12 High Gain 0-30 -15 - +15 dB Gain of the high range
13 Balance 0-100
D100:0 -
WD0:100W
Volume balance between the direct
sound (D) and the flanger sound
(W)
14 Level 0-127 0-127 Output Level
● 0128: 2Band Flanger
A flanger that lets you apply an effect independently to the low-frequency and
high-frequency ranges.
No Parameter Value Description
1 Split Freq 0-16 200-8000 Hz
Frequency at which the low and
high ranges will be divided
2 Low Pre Delay 0-125 0.0-100.0 ms
Delay time from when the original
sound is heard to when the low-
range flanger sound is heard
3 Low Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
4 Low Rate #1 1-127 0.05-10.00 Hz
Rate at which the low-range flanger
sound is modulated (Hz)
5 Low Rate 0-21 note
Rate at which the low-range flanger
sound is modulated (note)
6 Low Depth 0-127 0-127
Modulation depth for the low-range
flanger sound
7 Low Phase 0-90 0-180 deg
Spaciousness of the low-range
flanger sound
8 Low Feedback 0-98 -98 - +98%
Proportion of the low-range flanger
sound that is to be returned to the
input (negative values invert the
phase)
9 High Pre Delay 0-125 0.0-100.0 ms
Delay time from when the original
sound is heard to when the
high-range flanger sound is heard
10 High Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
11 High Rate #2 1-127 0.05-10.00 Hz
Rate at which the high-range
flanger sound is modulated (Hz)
12 High Rate 0-21 note
Rate at which the high-range
flanger sound is modulated (note)
13 High Depth 0-127 0-127
Modulation depth for the
high-range flanger sound
14 High Phase 0-90 0-180 deg
Spaciousness of the high-range
flanger sound
15 High Feedback 0-98 -98 - +98%
Proportion of the high-range
flanger sound that is to be
returned to the input (negative
values invert the phase)
16 Balance 0-100
D100:0W -
D0:100W
Volume balance of the original
sound (D) and flanger sound (W)
17 Level 0-127 0-127 Output volume
● 0121: Auto Wah
Cyclically controls a filter to create cyclic change in timbre.
No Parameter Value Description
1 Filter Type 0-1 Lpf, Bpf
Type of filter
Lpf: The wah effect will be applied
over a wide frequency range.
Bpf: The wah effect will be applied
over a narrow frequency range.
2 Manual #2 0-127 0-127
Adjusts the center frequency at
which the effect is applied.
3 Peak 0-127 0-127
Adjusts the amount of the wah
effect that will occur in the range
of the center frequency. Set a
higher value for Q to narrow the
range to be affected.
4 Sens 0-127 0-127
Adjusts the sensitivity with which
the filter is controlled.
5 Polarity 0-1 Up, Down
Sets the direction in which the
frequency will change when the
autowah filter is modulated. Up:
The filter will change toward a
higher frequency. Down: The filter
will change toward a lower
frequency.
6 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
7 Rate #1 1-127 0.05-10.00 Hz Frequency of modulation (Hz)
8 Rate 0-21 note Frequency of modulation (note)
9 Depth 0-127 0-127 Depth of modulation
10 Phase 0-90 0-180 deg
Adjusts the degree of phase shift
of the left and right sounds when
the wah effect is applied.
11 Low Gain 0-30 -15 - +15 dB Gain of the low range
12 High Gain 0-30 -15 - +15 dB Gain of the high range
13 Level 0-127 0-127 Output Level