Roland MIDI Implementation DP990F - Manual (Page 10)

10
3. Parameter Address Map (Model ID = 42H)
This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters which can be transferred using and “Data set 1 (DT1).”
All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form.
■Address Block map
An outlined address map of the Exclusive Communication is as follows;
Address (H) Block
40 00 00
Individual
40 01 3F
SYSTEM PARAMETERS
40 1×00
Individual
40 2×5A
PART PARAMETERS（x＝0-F）
41 m0 00
Individual
41 m8 7F
DRUM SETUP PARAMETERS
（m＝0-1）
48 00 00
SYSTEM PARAMETERS
Bulk
48 01 10
Bulk
48 1D 0F
PART PARAMETERS
49 m0 00
Bulk
49 mE 17
DRUM SETUP PARAMETERS
（m＝0-1）
There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individual parameters are transmitted one by one, and Bulk Dump
Transmission in which a large amount of data is transmitted at once.
■Individual Parameters
Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of “F0 ..... F7”).
In Individual Parameter Transmission, you must use the Address and Size listed in the following “Parameter Address Map.” Addresses marked at “#” cannot be used
as starting addresses.
●System Parameters
Parameters related to the system of the device are called System Parameters.
Address (H) Size (H) Data (H) Parameter Description Default Value (H) Description
40 00 00 00 00 04 0018-07E8 MASTER TUNE -100.0 - +100.0 [cent] 00 04 00 00 0 [cent]
40 00 01# Use nibblized data.
40 00 02#
40 00 03#
*Refer to section 4. Supplementary material, “About tuning.”
40 00 04 00 00 01 00-7F MASTER VOLUME 0-127 7F 127
(= F0 7F 7F 04 01 00 vv F7)
40 00 05 00 00 01 28-58 MASTER KEY-SHIFT -24 - +24 [semitones] 40 0 [semitones]
40 00 06 00 00 01 01-7F MASTER PAN -63 (LEFT) - +63 (RIGHT) 40 0 (CENTER)
40 00 7F 00 00 01 00 MODE SET 00 = GS Reset,
127 = Exit GS mode
(Rx. only)
* Refer to “System exclusive messages related to mode settings”.
40 01 10 00 00 10 00-40 VOICE RESERVE Part 10 (Drum Part) 02 2
40 01 11# Part 1 06 6
40 01 12# Part 2 02 2
40 01 13# Part 3 02 2
40 01 14# Part 4 02 2
40 01 15# Part 5 02 2
40 01 16# Part 6 02 2
40 01 17# Part 7 02 2
40 01 18# Part 8 02 2
40 01 19# Part 9 02 2
40 01 1A# Part 11 00 0
40 01 :# : : :
40 01 1F# Part 16 00 0
* The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. The maximum polyphony of this
instrument is 128. For compatibility with other GS models, it is recommended that the maximum polyphony be equal or less than 24.
40 01 30 00 00 01 00-07 REVERB MACRO 00: Room 1 04 Hall 2
01: Room 2