Roland MIDI Implementation DP990F - Manual (Page 22)

22
● 0103: Humanizer
Adds a vowel character to the sound, making it similar to a human voice.
No Parameter Value Description
1 Drive Sw 0-1 Off, On Turns Drive on/off.
2 Drive #2 0-127 0-127
Degree of distortion Also changes
the volume.
3 Vowel1 0-4 a, e, i, o, u Selects the vowel.
4 Vowel2 0-4 a, e, i, o, u Selects the vowel.
5 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
6 Rate 1-127 0.05-10.00 Hz
Frequency at which the two vowels
switch (Hz)
7 Rate #1 0-21 note
Frequency at which the two vowels
switch (note)
8 Depth 0-127 0-127 Effect depth
9 Input Sync Sw 0-1 Off, On
Determines whether the LFO for
switching the vowels is reset by
the input signal (ON) or not (OFF).
10 Input Sync Threshold 0-127 0-127
Volume level at which reset is
applied
11 Manual 0-100 0-100
Point at which Vowel 1/2 switch
49 or less: Vowel 1 will have a
longer duration.
50: Vowel 1 and 2 will be of equal
duration.
51 or more: Vowel 2 will have a
longer duration.
12 Low Gain 0-30 -15 - +15 dB Gain of the low frequency range
13 High Gain 0-30 -15 - +15 dB Gain of the high frequency range
14 Pan 0-127 L64 - 63R Stereo location of the output
15 Level 0-127 0-127 Output level
● 012b: Ring Modulator
This is an effect that applies amplitude modulation (AM) to the input signal,
producing bell-like sounds. You can also change the modulation frequency in
response to changes in the volume of the sound sent into the effect.
No Parameter Value Description
1 Frequency #1 0-127 0-127
Adjusts the frequency at which
modulation is applied.
2 Sens 0-127 0-127
Adjusts the amount of frequency
modulation applied.
3 Polarity 0-1 Up, Down
Determines whether the frequency
modulation moves towards higher
frequencies (Up) or lower
frequencies (Down).
4 Low Gain 0-30 -15 - +15 dB Gain of the low frequency range
5 High Gain 0-30 -15 - +15 dB Gain of the high frequency range
6 Balance #2 0-100
D100:0W -
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
7 Level 0-127 0-127 Output level
● 0125: Tremolo
Cyclically modulates the volume to add tremolo effect to the sound.
No Parameter Value Description
1 Mod Wave 0-4
Tri, Sqr, Sin,
Saw1, Saw2
Modulation Wave
Tri: Triangle wave
Sqr: Square wave
Sin: Sine wave
Saw1/2: Sawtooth wave
2 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
3 Rate #1 1-127 0.05 - 10.00 Hz Frequency of the change (Hz)
4 Rate 0-21 note Frequency of the change (note)
5 Depth #2 0-127 0-127 Depth to which the effect is applied
6 Low Gain 0-30 -15 - +15 dB Gain of the low range
7 High Gain 0-30 -15 - +15 dB Gain of the high range
8 Level 0-127 0-127 Output Level
● 0126: Auto Pan
Cyclically modulates the stereo location of the sound.
No Parameter Value Description
1 Mod Wave 0-4
Tri, Sqr, Sin,
Saw1, Saw2
Modulation Wave
Tri: Triangle wave
Sqr: Square wave
Sin: Sine wave
Saw1/2: Sawtooth wave
2 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
3 Rate #1 1-127 0.05 - 10.00 Hz Frequency of the change (Hz)
4 Rate 0-21 note Frequency of the change (note)
5 Depth #2 0-127 0-127 Depth to which the effect is applied
6 Low Gain 0-30 -15 - +15 dB Gain of the low range
7 High Gain 0-30 -15 - +15 dB Gain of the high range
8 Level 0-127 0-127 Output Level
● 012c: Slicer
By applying successive cuts to the sound, this effect turns a conventional
sound into a sound that appears to be played as a backing phrase. This is
especially effective when applied to sustain-type sounds.
No Parameter Value Description
1 Rate Mode 0-1 Hz, note
When this is set to “note,” the
effect is synchronized with the
tempo.
2 Rate 1-127 0.05-10.00 Hz
Rate at which the 16-step sequence
will cycle (Hz)
3 Rate #1 12-21 note
Rate at which the 16-step sequence
will cycle (note)
4 Attack 0-127 0-127
Speed at which the level changes
between steps
5 Input Sync Sw 0-1 Off, On
Specifies whether an input note will
cause the sequence to resume
from the first step of the sequence
(ON) or not (OFF)
6 Input Sync Threshold 0-127 0-127
Volume at which an input note will
be detected
Sets the manner in which the
volume changes as one step
progresses to the next.
Legato: The change in volume from
one step’s level to the next
remains unaltered. If the level of a
following step is the same as the
one preceding it, there is no
change in volume.
7 Mode 0-1 Legato, Slash
Slash: The level is momentarily set
to 0 before progressing to the
level of the next step. This change
in volume occurs even if the level
of the following step is the same as
the preceding step.
8 Shuffle #2 0-127 0-127
Timing of volume changes for
even- numbered steps (step 2,
step 4, step 6...). The higher the
value, the later the beat
progresses.
9 Level 0-127 0-127 Output level