Roland MIDI Implementation DP990F - Manual (Page 19)

19
● 0107: Speaker Simulator
Simulates the speaker type and mic settings used to record the speaker sound.
No Parameter Value Description
1 Speaker Type #1 0-15 (See the table.) Type of speaker
2 Mic Setting 0-2 1, 2, 3
Adjusts the location of the mic that
is recording the sound of the
speaker.
This can be adjusted in three steps,
with the mic becoming more
distant in the order of 1, 2, and 3.
3 Mic Level 0-127 0-127 Volume of the microphone
4 Direct Level 0-127 0-127 Volume of the direct sound
5 Level #2 0-127 0-127 Output Level
Specifications of each Speaker Type
The speaker column indicates the diameter of each speaker unit (in inches) and
the number of units.
Type Cabinet Speaker Microphone
Small 1 Small open-back enclosure 10 Dynamic
Small 2 Small open-back enclosure 10 Dynamic
Middle Open back enclosure 12 x 1 Dynamic
JC-120 Open back enclosure 12 x 2 Dynamic
Built-In 1 Open back enclosure 12 x 2 Dynamic
Built-In 2 Open back enclosure 12 x 2 Condenser
Built-In 3 Open back enclosure 12 x 2 Condenser
Built-In 4 Open back enclosure 12 x 2 Condenser
Built-In 5 Open back enclosure 12 x 2 Condenser
BG Stack 1 Sealed enclosure 12 x 2 Condenser
BG Stack 2 Large sealed enclosure 12 x 2 Condenser
MS Stack 1 Large sealed enclosure 12 x 4 Condenser
MS Stack 2 Large sealed enclosure 12 x 4 Condenser
Metal Stack Large double stack 12 x 4 Condenser
2-Stack Large double stack 12 x 4 Condenser
3-Stack Large triple stack 12 x 4 Condenser
● 0114: Guitar Amp Simulator
This is an effect that simulates the sound of a guitar amplifier.
No Parameter Value Description
1 Pre Amp Sw 0-1 Off, On Turns the amp switch on/off.
2 Pre Amp Type #1 0-13
JC-120,
Clean Twin,
MATCH Drive,
BG Lead,
MS1959I,
MS1959II,
MS1959I+II,
SLDN Lead,
Metal 5150,
Metal Lead,
OD-1,
OD-2 Turbo,
Distortion,
Fuzz
Type of guitar amp
3 Pre Amp Volume 0-127 0-127
Volume and amount of distortion of
the amp
4 Pre Amp Master 0-127 0-127 Volume of the entire pre-amp
5 Pre Amp Gain 0-2
Low, Middle,
High
Amount of pre-amp distortion
6 Pre Amp Bass 0-127 0-127
7 Pre Amp Middle 0-127 0-127
8 Pre Amp Treble 0-127 0-127
Tone of the bass/mid/treble
frequency range
Middle cannot be set if “MATCH
Drive” is selected as the Pre Amp
Type.
9 Pre Amp Presence 0-127
0-127 (MATCH
Drive: -127-0)
Tone for the ultra-high frequency
range
10 Pre Amp Bright 0-1 Off, On
Turning this “On” produces a
sharper and brighter sound.
This parameter applies to the
“JC-120,” “Clean Twin,” and “BG
Lead” Pre Amp Types.
11 Speaker Sw 0-1 Off, On
Determines whether the signal
passes through the speaker (ON),
or not (OFF).
12 Speaker Type #2 0-15 (See the table.) Type of speaker
13 Mic Setting 0-2 1, 2, 3
Adjusts the location of the mic
that’s capturing the sound of the
speaker.
This can be adjusted in three steps,
from 1 to 3, with the mic becoming
more distant as the value
ncreases.
14 Mic Level 0-127 0-127 Volume of the microphone
15 Direct Level 0-127 0-127 Volume of the direct sound
16 Pan 0-127 L64 - 63R Stereo location of the output
17 Level 0-127 0-127 Output level
Specifications of each Speaker Type
The speaker column indicates the diameter of each speaker unit (in inches) and
the number of units.
Type Cabinet Speaker Microphone
Small 1 Small open-back enclosure 10 Dynamic
Small 2 Small open-back enclosure 10 Dynamic
Middle Open back enclosure 12 x 1 Dynamic
JC-120 Open back enclosure 12 x 2 Dynamic
Built-In 1 Open back enclosure 12 x 2 Dynamic
Built-In 2 Open back enclosure 12 x 2 Condenser
Built-In 3 Open back enclosure 12 x 2 Condenser
Built-In 4 Open back enclosure 12 x 2 Condenser
Built-In 5 Open back enclosure 12 x 2 Condenser
BG Stack 1 Sealed enclosure 12 x 2 Condenser
BG Stack 2 Large sealed enclosure 12 x 2 Condenser
MS Stack 1 Large sealed enclosure 12 x 4 Condenser
MS Stack 2 Large sealed enclosure 12 x 4 Condenser
Metal Stack Large double stack 12 x 4 Condenser
2-Stack Large double stack 12 x 4 Condenser
3-Stack Large triple stack 12 x 4 Condenser