Pioneer DVJ-1000 - Manual (Page 41)

Advanced Operations
English
39
En
Advanced Operations
REV
FWD
DIRECTION
HOT CUE
REC MODE
LOOP
OUT ADJUST
TEMPO
IN ADJUST
ENTER
CUE
REALTIME CUE IN OUT RELOOP/ EXIT 4-BEAT ONE-TRACK CUE / LOOP CALL
BACK & FORTH
ANGLE SUBTITLE AUDIO DISPLAY DELETE MEMORY MENU T.MENU RETURN SETUP
TOUCH/BRAKE
RELEASE/START
JOG MODE
VINYL
HYPERJOG MODE
TEMPO
MASTER TEMPO
WIDE
TEXT MODE
TIME MODE AUTO CUE
DVD TITLE MP3 FOLDER
JOG ADJUST LIGHT
HEAVY
TEMPO
RESET
REV FWD
POWER OFF ON STOP
LOCK UNLOCK
EJECT
PLAY/PAUSE
DVJ-1000
PREVIOUS NEXT
FWD REV
PLAY/PAUSE
6
JOG MODE
RELEASE/
START
TOUCH/
BRAKE
C
A
B
HOT CUE
HOT CUE
REC MODE
IN/
REALTIME CUE/
IN ADJUST
OUT/
OUT ADJUST
HYPERJOG
MODE
NORMAL/DJ
Jog dial
Scratch play
★ This function is not supported when the rear panel NORMAL/DJ
switch is set to the NORMAL position.
When the jog mode is set to VINYL mode ON, pressing the jog dial’s top
panel while rotating the dial will cause audio and video to be output in
proportion to the direction and speed of jog dial rotation.
1. Press the JOG MODE select button so that the VINYL
mode indicator lights.
2. During playback, press the top of the jog dial.
¶ Playback will slow and come to a stop (the time required to com-
plete stop can be set independently).
¶ If the jog dial is rotated as playback slows but before it has com-
pletely stopped, sound will be interrupted suddenly, and will then
start again, but in the direction corresponding to the direction the
jog dial is rotated in step 3.
3. Rotate the jog dial in the desired direction of playback.
¶ Playback will occur in proportion to the direction and speed of jog
dial rotation.
4. Release hand from surface of jog dial.
¶ Playback will return to its original status (the time required until
full acceleration can be set independently).
■ To set the deceleration time (time until playback fully stops
when jog dial surface is pressed)
Rotate the TOUCH/BRAKE response dial.
¶ The time till playback stops changes.
¶ This is the same setting as the deceleration speed adjustment
used when the PLAY/PAUSE ( 6) button is pressed in VINYL
mode to temporarily pause playback.
■ To set the acceleration time (time until playback fully re-
gains original speed when hand is released from jog dial
surface)
Rotate the RELEASE/START response dial.
¶ The time till playback returns to normal speed changes.
¶ This is the same setting as the acceleration speed adjustment
used when the PLAY/PAUSE ( 6) button is pressed in VINYL
mode to resume playback.
[Hyper jog mode]
When jog mode is set to VINYL mode ON, press the HYPERJOG MODE
button so that the indicator lights. When the jog dial is then rotated, the
amount of sound or image change will quadruple (x4) in response to the
rotation angle of the dial.
Spin play
★ This function is not supported when the rear panel NORMAL/DJ
switch is set to the NORMAL position.
With VINYL mode ON, press the surface of the jog dial, or press the
PLAY/PAUSE (
6) button to set the unit to pause, then rotate the jog
dial quickly; even if you remove your hand from the jog dial, playback will
occur in proportion to the direction and speed of the jog dial rotation.
Braking
★ This function is not supported when the rear panel NORMAL/DJ
switch is set to the NORMAL position.
¶ During playback in VINYL mode, if the PLAY/PAUSE (6) button is
pressed to pause playback, the sound decelerates at the braking speed
set with the TOUCH/BRAKE dial.
¶ When the PLAY/PAUSE (6) button is pressed once again to resume
playback, the sound accelerates at the speed set with the RELEASE/
START dial.
Hot cue
★ This function is not supported when the rear panel NORMAL/DJ
switch is set to the NORMAL position.
This function allows playback to be started quickly from one of three
points (A, B, C), by previous setting of cue point and loop information.
¶ Storing to memory may not be possible while the jog dial’s audio/
video memory status display is flashing.
■ Setting hot cue point
1. Press the HOT CUE REC MODE button so that the HOT
CUE A, B, and C button indicators light red.
2. During playback, pause mode or cue standby mode, find
the point you wish to use as the hot cue, and at that point
press the button (A, B, or C) in which you wish to store
the cue information.
¶ The button memory will recorded with the time position data and
playback method.
¶ The pressed button will flash red for about 2 seconds, then light
steadily.
¶ During DVD playback, a thumbnail of the hot cue point will be
displayed on the preview monitor screen.
¶ If the HOT CUE button is pressed during the loop setting mode
(while OUT/OUT ADJUST and IN/REALTIME CUE/IN ADJUST
buttons are flashing), the currently playing loop information will be
stored in memory.
¶ If a memory card is loaded, the data recorded to the HOT CUE
button will be stored on the memory card; in this way, the previ-
ously set information can be called up quickly when playing the
same disc at a later date (
☞ P.43).
Buttons and controls with the mark are disabled when
the NORMAL/DJ switch is set to NORMAL.