Appendix e: regulatory information, Fcc statement, Fcc radiation exposure statement – Linksys E2100L User Manual
Page 62: Safety notices, Industry canada statement, Avis d’industrie canada, Linksys e2100l appendix e: regulatory information, Industry canada radiation exposure statement

Linksys E2100L
Appendix E: Regulatory Information
59
Advanced Wireless-N Router
Appendix E: Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules . 
Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this 
device must accept any interference received, including 
interference that may cause undesired operation .
This product has been tested and complies with the 
specifications for a Class B digital device, pursuant to Part 
15 of the FCC Rules . These limits are designed to provide 
reasonable protection against harmful interference in 
a residential installation . This equipment generates, 
uses, and can radiate radio frequency energy and, if not 
installed and used according to the instructions, may 
cause harmful interference to radio communications . 
However, there is no guarantee that interference will not 
occur in a particular installation . If this equipment does 
cause harmful interference to radio or television reception, 
which is found by turning the equipment off and on, the 
user is encouraged to try to correct the interference by 
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or 
devices
•
Connect the equipment to an outlet other than the 
receiver’s
•
Consult a dealer or an experienced radio/TV technician 
for assistance
FCC Caution: Any changes or modifications not expressly 
approved by the party responsible for compliance could 
void the user’s authority to operate this equipment .
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure 
limits set forth for an uncontrolled environment . This 
equipment should be installed and operated with 
minimum distance 20 cm between the radiator and your 
body .
This transmitter must not be co-located or operating in 
conjunction with any other antenna or transmitter . IEEE 
802 .11b or 802 .11g operation of this product in the USA is 
firmware-limited to channels 1 through 11 .
Safety Notices
WARNING:
Do not use this product near water,
for example, in a wet basement or near a 
swimming pool .
WARNING:
Avoid using this product during an
electrical storm . There may be a remote risk of 
electric shock from lightning .
WARNING:
This product contains lead, known
to the State of California to cause cancer, and 
birth defects or other reproductive harm . Wash 
hands after handling .
Industry Canada Statement
This Class B digital apparatus complies with Canadian 
ICES-003 and RSS210 .
Operation is subject to the following two conditions:
1 . This device may not cause interference and
2 . This device must accept any interference, including 
interference that may cause undesired operation of 
the device . This device has been designed to operate 
with an antenna having a maximum gain of 2 dBi . 
Antenna having a higher gain is strictly prohibited per 
regulations of Industry Canada . The required antenna 
impedance is 50 ohms . 
Industry Canada Radiation Exposure 
Statement:
This equipment complies with IC radiation exposure limits 
set forth for an uncontrolled environment . This equipment 
should be installed and operated with minimum distance 
20 cm between the radiator & your body .
This transmitter must not be co-located or operating in 
conjunction with any other antenna or transmitter .
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme aux 
normes NMB-003 et RSS210 du Canada .
L’utilisation de ce dispositif est autorisée seulement aux 
conditions suivantes :
1 . il ne doit pas produire de brouillage et 
2 . il doit accepter tout brouillage radioélectrique reçu, 
même si ce brouillage est susceptible de compromettre 
le fonctionnement du dispositif . Le dispositif a été 
conçu pour fonctionner avec une antenne ayant un 
gain maximum de 2 dBi . Les règlements d’Industrie 
Canada interdisent strictement l’utilisation d’antennes 
dont le gain est supérieur à cette limite . L’impédance 
requise de l’antenne est de 50 ohms . 
Avis d’Industrie Canada concernant 
l’exposition aux radiofréquences :
Ce matériel est conforme aux limites établies par IC 
en matière d’exposition aux radiofréquences dans un 
