Cleaning and replacing the filter cover – JVC DLA-G150CLE User Manual

Page 32

DLA-G150CLU

DLA-G150CLE

1-32

No.51931

ENGLISH

DEUTSH

FRAN

ÇAIS

ITALIANO

ESPAÑOL

Cleaning and Replacing the Filter Cover

Clean the filter regularly. If the filter is heavily stained and does not clean, or if it is damaged, replace the filter with a new filter.
Otherwise, dirt may get inside and appear on the screen, preventing you from fully enjoying the video image. If dirt gets inside
or if you need information about the filter, consult authorized dealer where you purchased the projector or the nearest Service
Center.

Turn off the MAIN POWER switch.

After the projector goes into stand-by state with the STAND BY indicator on, turn off the MAIN POWER switch and pull
out the power cord from the projector and the wall outlet.

Remove the filter.

Loosen the screw with a flat-end screwdriver.

Notes

• The screw is fitted so that it does not come off the filter.
• If the filter is clogged with dirt, etc., the projector goes into an warning state (the OPERATE and STAND BY indicator blink.

etc.). Therefore regularly, clean the filter. For the warning indication, refer to page 67.

Clean the filter.

Clean the filter with a neutral detergent, wash it in water, and then dry it in the shade.

CAUTIONS

• Put on rubber gloves when using neutral detergent.
• After you have washed the filter in water, make sure the filter is completely dry before reinstalling it, otherwise an electric

shock or malfunction could occur.

• Do not clean the filter using a vacuum cleaner. Since the filter is soft, it may be sucked into the vacuum cleaner or damaged.

Reinstall the filter.

Fasten the screw with a flat-end screwdriver.

Notes

• Install the filter correctly. Otherwise, the projector does not operate. (Goes into an warning state (For the warning indication,

Refer to page 66).)

• If the filter’s claws (in particular the claw which is hidden behind the filter cover knob) are damaged, the projector may not

operate. Then, replace with a new filter.

Screw

Filter

Be careful not to
damage the claws.

Replacing the Light-Source Lamp

■

Resetting the Lamp Use Time

After replacing with a new light-source lamp, reset the lamp-time counter inside the projector to clear the accumulated lamp
time to zero (0). After resetting, a new count will start for the new light-source lamp.

■

Projector’s button

Turn on the MAIN POWER switch to go
into stand-by mode.

In stand-by mode, the STAND BY indicator on the
projector lights up.

Press the following buttons on the
projector, sequentially.

Momentary press the PC button.

Momentary press the ENTER button.

Momentary press the EXIT button.

Press and hold the HIDE button for two seconds
or more.

* During this sequence, the STAND BY and OPERATE

indicators alternately blink about every approx. 3 seconds.
After completion of the sequence, the STAND BY indicator
alone stays on.

* Buttons must be pressed within 2 seconds of the previous

button.

* When you make a mistake in button operations, return to

the beginning of the sequence.

* To check the lamp time on the menu, press the MENU button

and select “Information” with the cursor button

∞

The lamp use time is indicated in the item “Lamp time”.

Video main menu

PC main menu

CAUTION

• Reset the lamp use time only when you have replaced with

a new light-source lamp. Never reset it during lamp life,
otherwise the replacement time may become unclear, and
lead to degraded performance or lamp explosion.

LAMP

TEMP

STAND BY

HIDE

VIDEO

MENU

KEYSTONE

PRESET

EXIT

ENTER

OPERATE

Cursor buttons

5/∞

PC
button

ENTER
button

EXIT
button

HIDE
button

STAND BY
indicator

MENU
button

OPERATE
indicator

Input

Switcher

Source

Lamp time

VIDEO

CH.0

NTSC

123 h

Image adj.

Setting

Color temp.

Options

Language

Information

Lamp time (0 h)

Input

Switcher

Resolution

Frequency H

Frequency V