JVC LVT1112-001A - Manual (Page 28)

24
3 Press the numeric buttons (1 – 10, +10) to select
a channel number while the channel number
position is flashing.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
4
Press MEMORY again while the selected channel
number is flashing on the display.
The station is assigned to the selected channel number.
• The selected channel number stops flashing.
5
Press repeatedly or hold TUNING 9 or
TUNING ( to select another frequency you want
to store.
6 Repeat steps 1 to 5 until you store all the
stations you want.
To erase a stored preset station
Storing a new station on a used channel number erases the
previously stored one.
To tune in a preset station
From the remote control:
1
Press FM/AM to select the band.
The last received station of the selected band is tuned in and the
numeric buttons now work for tuner operations.
• Each time you press the button, the band alternates between
FM and AM (MW).
2
Press the numeric buttons (1 – 10, +10) to select
a channel number.
If you select “FM” or “AM” using SOURCE SELECTOR on the
front panel, press FM/AM on the remote control before this
operation.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
2 again.
1
Turn SOURCE SELECTOR to select “FM” or
“AM.”
The last received station of the selected band is tuned in.
2
Press TUNER PRESET.
“P” appears on the display and MULTI JOG now works for
selecting preset channels.
3
Turn MULTI JOG to select a preset channel
number during “P” appears on the display.
• Turning MULTI JOG clockwise increases the preset channel
numbers.
• Turning MULTI JOG counterclockwise decreases the preset
channel numbers.
Selecting the FM reception mode
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station (see
page 23).
From the remote control ONLY:
While listening to an FM station, press FM MODE.
If you select “FM” using SOURCE SELECTOR on the front panel,
press FM/AM on the remote control before this operation.
• Each time you press the button, the FM reception mode alternates
between “AUTO MUTING” and “MONO.”
AUTO MUTING*: Normally select this.
When a program is broadcast in stereo, you
will hear stereo sound; when in monaural, you
will hear monaural sound. This mode is also
useful to suppress static noise between
stations. The AUTO MUTING indicator lights
up on the display.
MONO: Select this to improve the reception (but
stereo effect will be lost).
In this mode, you will hear noise while tuning
in to the stations. The AUTO MUTING
indicator goes off from the display. (The ST
indicator also goes off.)
* Initial setting
ANALOG
SUBWFR
ST TUNED AUTO MUTING
MH Z
VOL
L R
ANALOG
SUBWFR
ST TUNED AUTO MUTING
MH Z
VOL
L R
STANDBY / ON STANDBY
TV DIRECT SETTING ADJUST SURROUND
DVD MULTI DVD STB VR TV FM / AM
SET / TUNER PRESET SOURCE SELECTOR MASTER VOLUME
PHONES / MULTI JOG
ANALOG
SUBWFR
ST TUNED AUTO MUTING
MH Z
VOL
L R
Tuner operations
ANALOG
SUBWFR
ST TUNED AUTO MUTING
MH Z
VOL
L R
ANALOG
SUBWFR
ST TUNED AUTO MUTING
MH Z
VOL
L R
23-27_RX-ES9SL[B]f 03.6.27, 16:46 24