Sound adjustments, Operating procedure, Adjusting the tone—bass, treble – JVC LVT1112-001A User Manual
Page 25: Adjusting the subwoofer output level —subwfr, On the front panel, Press adjust, When using the remote control, Press tone, Bass treble panorama b.boost att, Subwfr surr r effect surr l bal center
21
Sound adjustments
When operating the receiver using the remote control, always set the mode selector to AUDIO/TV/VCR/STB.
Operating procedure
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1 again.
1
Press ADJUST.
MULTI JOG now works for the sound adjustment.
2
Turn MULTI JOG until the setting item you want
to set appears on the display, then press SET.
• As you turn MULTI JOG, the indication changes as follows:
3
Turn MULTI JOG to adjust the item selected in
step
2, then press SET.
Your setting is stored.
Ex.: When selecting “+10 (dB)” for “BASS”.
STANDBY / ON
STANDBY
TV DIRECT
SETTING
ADJUST
SURROUND
DVD MULTI
DVD
STB
VR
TV
FM / AM
SET / TUNER PRESET
SOURCE SELECTOR
MASTER VOLUME
PHONES
/ MULTI JOG
DVD
AUDIO/TV
/VCR/STB
Adjusting the tone—BASS, TREBLE
You can adjust the bass and treble sounds to your preference.
• You have to make these adjustments for each source.
BASS*:
To adjust the bass (from –10 dB to +10 dB).
TREBLE*:
To adjust the treble (from –10 dB to +10 dB).
* “0” is the initial setting.
When using the remote control:
1
Press TONE.
2
Press BASS
9/( or
TREBLE
9/( to adjust the
sound level (from –10 dB to
+10 dB).
NOTE
When you use the numeric buttons to operate your target source after
tone adjustments, press the corresponding source selecting button
first so that the numeric buttons work for your target source.
Adjusting the subwoofer output level
—SUBWFR
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“USE” for the
Quick Setup or “YES” for the Manual Setup (see pages 16 and 17).
• You have to make this adjustment for each source.
SUBWFR*:
To adjust the subwoofer output level (from –10 dB to
+10 dB).
* “0” is the initial setting.
When using the remote control:
Press SUBWFR +/– to adjust the
subwoofer output level (from –10 dB
to +10 dB).
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR
CENTER
L
R
SURR
BASS BOOST
A.POSITION
SMART S. SETUP
SLEEP
CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN
100+
BASS
TREBLE
SUBTITLE
RETURN
TITLE/GROUP
BASS
TREBLE
1
2
3
4
VFP
INPUT
TONE
TEST
EFFECT
DECODE
5
6
7
8
9
10
3D
0
+10
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR
CENTER
L
R
SURR
BASS BOOST
A.POSITION
SMART S. SETUP
SLEEP
CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN
100+
BASS
TREBLE
SUBTITLE
RETURN
TITLE/GROUP
BASS
TREBLE
1
2
3
4
VFP
INPUT
TONE
TEST
EFFECT
DECODE
5
6
7
8
9
10
3D
0
+10
ANALOG
SUBWFR
VOL
L
R
ANALOG
SUBWFR
VOL
L
R
BASS
TREBLE
PANORAMA
B.BOOST
ATT
(Back to the beginning)
SUBWFR
SURR R
EFFECT
SURR L
BAL
CENTER
21-22_RX-ES9SL[B]f
03.6.27, 16:45
21