JVC LVT1112-001A - Manual (Page 16)

12
3
Adjust the volume
To increase the volume, turn MASTER VOLUME
control clockwise (or press VOLUME + on the
remote control).
To decrease the volume, turn MASTER VOLUME
control counterclockwise (or press VOLUME – on
the remote control).
CAUTION:
Always set the volume to the minimum before starting any sources. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
NOTE
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
Listening with headphones
Connect a pair of headphones to the PHONES jack on the front
panel
. This cancels the Surround mode currently selected,
deactivates speakers, and activates the HEADPHONE mode.
The HP (headphone) indicator lights up on the display.
• Disconnecting a pair of headphone from the PHONES jack cancels
the HEADPHONE mode and activates the speakers.
SUBWFR LFE
VOL
L C R
LS RS
DOLBY D
DGTL AUTO
DGTL DTS
DGTL D.D.
HEADPHONE mode
When using the headphones, the following signal is output
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signal is
output directly from the left and right headphones.
— For multi-channel sources, the front left and right, center and
surround channel signal is down-mixed and then output from
the headphones without missing bass element.
You can enjoy multi-channel sound source using the
headphones.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before removing headphones, as high volume may output from the
speakers.
Selecting the digital decode mode
If the following symptoms occur while playing Dolby Digital or DTS
Digital Surround software with “DGTL AUTO” selected (see page 11),
follow the procedure below:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching for or skipping chapters or tracks.
From the remote control ONLY:
1 Press ANALOG/DIGITAL INPUT to select “DGTL
AUTO.”
2
Press DECODE to select “DGTL D.D.” or “DGTL
DTS.”
• Each time you press the button, the digital input mode changes
as follows:
• To play back software encoded with Dolby Digital, select “DGTL
D.D.”
• To play back software encoded with DTS Digital Surround,
select “DGTL DTS.”
NOTE
When you turn off the power or select another source, “DGTL DTS” or
“DGTL D.D.” is canceled and the digital input mode is automatically
reset to “DGTL AUTO.”
Basic operations
When operating the receiver
using the remote control,
always set the mode selector
to AUDIO/TV/VCR/STB.
TV DIRECT
DVD VCR STB TV
DVD VR STB TV
DVD MULTI
TV VOL CHANNEL
TUNING TUNING
DVD
AUDIO/TV
/VCR/STB
FM MODE
MEMORY
TOP MENU
PTY
CHOICE
PTY SEARCH DISPLAY
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L R SURR
BASS BOOST A.POSITION SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100+
BASS TREBLE
SUBTITLE RETURN TITLE/GROUP
ON SCREEN
PTY
MENU TA/NEWS/INFO
VOLUME
FM/AM TV/VIDEO MUTING
AUDIO
HOME CINEMA CONTROL CENTER
BASS TREBLE
1 2 3
4 VFP
INPUT
TONE
TEST EFFECT DECODE
5 6
7 8 9
10
3D
0 +10
ENTER
STANDBY / ON STANDBY
TV DIRECT SETTING ADJUST SURROUND
DVD MULTI DVD STB VR TV FM / AM
SET / TUNER PRESET SOURCE SELECTOR MASTER VOLUME
PHONES / MULTI JOG
11-14_RX-ES9SL[B]f 03.6.27, 16:45 12