JVC LVT1112-001A - Manual (Page 15)

11
2
Select the source to play
On the front panel:
Turn SOURCE SELECTOR until the source name
you want appears on the display.
The source indicator corresponding to the selected source lights in
red.
• As you turn SOURCE SELECTOR, the source changes as follows:
From the remote control:
Press one of the source selecting buttons.
• Each time you press FM/AM, FM and AM (MW) changes
alternately.
DVD MULTI: Select the DVD player using the analogue
discrete output mode (5.1 channel reproduction).
To enjoy the DVD MULTI playback, see page 34.
DVD (DIGITAL) * : Select the DVD player.
STB (DIGITAL) * : Select the STB.
VR (DIGITAL) * : Select the VR.
TV: Select the TV tuner.
FM: Select an FM broadcast.
AM: Select an AM (MW) broadcast.
NOTE
After pressing VR on the remote control, you can operate the VCR by
using the remote control but not the VDR. See page 35 and 37 for
details.
* Selecting the analogue or digital input mode
When you have connected the VR, STB, or DVD player using both the
analogue connection and the digital connection methods (see pages 7
to 9), you need to select the correct input mode.
• You can select the digital input only for sources which you have
selected digital input terminals for. (See “Setting the digital input
(DIGITAL IN) terminals—DIGITAL IN” on page 19.)
From the remote control ONLY:
Press ANALOG/DIGITAL INPUT to select the
analogue or digital input mode.
• Each time you press the button, the input mode alternates between
the analogue input (“ANALOGUE”) and the digital input (“DGTL
AUTO”).
DGTL AUTO: Select for the digital input mode. The receiver
automatically detects the incoming signal format,
then the digital signal format indicator (DOLBY D,
DTS or LPCM) for the detected signals lights up.
ANALOGUE*: Select for the analogue input mode.
* Initial setting
NOTE
You cannot select the digital input mode when selecting “DVD MULTI”
as the playing source.
When operating the receiver
using the remote control,
always set the mode selector
to AUDIO/TV/VCR/STB.
Basic operations
ANALOG
SUBWFR LFE
VOL
L C R
LS RS
DVD MULTI DVD (DVD DIGITAL)
STB (STB DIGITAL)
TV VR (VR DIGITAL) FM AM
(Back to the beginning)
1
Turn on the power
Press STANDBY/ON (or AUDIO on the remote
control).
The STANDBY lamp goes off. The current source indicator lights in
red. The name of the current source (or station frequency) appears on
the display.
Current volume level is shown here.
Current source name appears.
To turn off the power (into standby)
Press STANDBY/ON again (or AUDIO on the remote control).
The STANDBY lamp lights up.
NOTE
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
STANDBY / ON STANDBY
TV DIRECT SETTING ADJUST SURROUND
DVD MULTI DVD STB VR TV FM / AM
SET / TUNER PRESET SOURCE SELECTOR MASTER VOLUME
PHONES / MULTI JOG
TV DIRECT
DVD VCR STB TV
DVD VR STB TV
DVD MULTI
TV VOL CHANNEL
TUNING TUNING
DVD
AUDIO/TV
/VCR/STB
FM MODE
MEMORY
TOP MENU
PTY
CHOICE
PTY SEARCH DISPLAY
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L R SURR
BASS BOOST A.POSITION SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100+
BASS TREBLE
SUBTITLE RETURN TITLE/GROUP
ON SCREEN
PTY
MENU TA/NEWS/INFO
VOLUME
FM/AM TV/VIDEO MUTING
AUDIO
HOME CINEMA CONTROL CENTER
BASS TREBLE
1 2 3
4 VFP
INPUT
TONE
TEST EFFECT DECODE
5 6
7 8 9
10
3D
0 +10
ENTER
ANALOG
SUBWFR LFE
VOL
L C R
LS RS
11-14_RX-ES9SL[B]f 03.6.27, 16:45 11