JAI AD-081GE User Manual
Ad-081ge, User's manual
Table of contents
Document Outline
- AD-081GE
- 1. General
- 2. Camera nomenclature
- 3. Main Features
- 4. Locations and functions
- 5. Pin configuration
- 5.1. 12-pin Multi-connector (DC-in/GPI
- 5.2. Digital Output Connector for Giga
- 5.3. 6-pin Multi-connector (LVDS IN an
- 5.4. DIP switches
- 5.4.1 Trigger input 75 ohms terminatio
- 5.4.2 EEN output
- 5.4.3 Video output for Auto iris lens
- 6. Input and output circuits
- 6.1. Iris Video output
- 6.2. Trigger input
- 6.3. EEN (Exposure Enable) output
- 7. System Configuration
- 7.1. System connection
- 7.2. Lens considerations
- 8. GPIO (Inputs and outputs)
- 8.1. Overview
- 8.1.1 LUT (Cross Point Switch)
- 8.1.2 12-bit Counter
- 8.1.3 Pulse Generators (0 to 3)
- 8.1.4 Opto-isolated Inputs/Outputs
- 8.1.5 Recommended External Input circu
- 8.1.6 Recommended External Output circ
- 8.1.7 Optical Interface Specifications
- 8.2. Inputs and outputs table
- 8.3. Configuring the GPIO module (regis
- 8.3.1 Input /Output Signal Selector
- 8.3.2 12bit counter
- 8.3.3 Pulse generators (20 bit x 4)
- 8.4. GPIO programming examples
- 8.4.1 GPIO Plus PWC shutter
- 8.4.2 Internal Trigger Generator
- 9. GigE Vision® Streaming Protocol (GVS
- 9.1. Digital Video Output (Bit Allocat
- 9.2. Bit Allocation (Pixel Format / Pi
- 9.2.1 GVSP_PIX_MONO8 (8bit)
- 9.2.2 GVSP_PIX_MONO10 (10bit)
- 9.2.3 GVSP_PIX_MONO10_PACKED (10 bit)
- 9.2.4 GVSP_PIX_MONO12 (12 bit)
- 9.2.5 GVSP_PIX_MONO12_PACKED (12 bit)
- 10. Functions and Operations
- 10.1. GigE Vision Standard Interface
- 10.2. Recommended Network Configuratio
- 10.2.1 Verified Network Interface Card
- 10.2.2 Video data rate (network bandwi
- 10.2.3 Disable Firewalls
- 10.2.4 Enabling Jumbo Frames
- 10.2.5 Setting Receive Descriptors
- 10.2.6 Interrupt Moderation rate
- 10.2.7 Calculating and setting Inter-P
- 10.2.8 Confirm the Filter Driver is us
- 10.2.9 Others
- 10.2.10 Note for 100BASE-TX connection
- 10.3. Basic functions
- 10.3.1 RJ-45 outputs
- 10.3.2 Sync mode (Register 0xA098)
- 10.3.3 High frame rate mode (Double sp
- 10.3.4 High dynamic range mode
- 10.3.5 High S/N mode
- 10.3.6 PIV ( Particle Image Velocimetr
- 10.3.7 Iris Video output
- 10.3.8 Auto-detect LVAL-sync / async a
- 10.3.9 Partial scan (Fast dump ON)
- 10.3.10 Vertical Binning
- 10.3.11 Electronic shutter
- 10.3.12 Shading correction
- 10.3.13 Knee compensation
- 10.3.14 Blemish compensation
- 10.3.15 Digital gain
- 10.3.16 Rear Panel Indicator
- 10.3.17 Test signal generator
- 10.4. Sensor Layout and Timing
- 10.4.1 Sensor Layout
- 10.4.2 Horizontal Timing
- 10.4.3 Vertical Timing
- 10.4.4 Partial Scan (when the start li
- 10.4.5 Vertical binning
- 10.5. Operation Mode
- 10.5.1 Continuous mode
- 10.5.2 Edge Pre-Select (EPS) trigger m
- 10.5.3 Pulse Width Control (PWC) trigg
- 10.5.4 Reset Continuous Trigger (RCT)
- 10.5.5 Particle Image Velocimetry
- 10.5.6 Sequential Trigger Mode (EPS)
- 10.5.7 Delayed Readout EPS and PWC Mod
- 10.5.8 Smearless mode
- 10.5.9 Optical Black transfer mode
- 10.5.10 Multi ROI mode (Multi Region o
- 10.6. Operation Mode and Functions mat
- 10.6.1 Readout Mode (0xA098) 0:SYNC
- 10.6.2 Readout mode (0xA098) 1:ASYNC
- 10.7. Special note for settings
- 10.7.1 When the image size is changed
- 10.7.2 When the image is captured
- 10.7.3 Acquisition frame rate
- 11. External Appearance and Dimensions
- 12. Specifications
- 12.1. Spectral response
- 12.2. Specifications Table
- Register Map
- Appendix
- 1. Precautions
- 2. Typical Sensor Characteristics
- 3. Caution when mounting a lens on the
- 4. Caution when mounting the camera
- 5. Exportation
- 6. References
- Change History
- User's Record