Integra DTR-10.5 - Manual (Page 61)

61
Operations
Using the Listening Modes —Continued
The DTR-10.5 provides various listening modes.
Note:
The available modes depend on the input signal you
selected.
Operating on the DTR-10.5
Operating with the Remote Controller
Tip:
A table listed later in this manual shows which listening
mode can be used with which input signal format. See
page 143.
Selecting the Listening Mode
1 Press the input source button.
2 Start playback on the device you selected
for input.
3 Press the [Listening Mode] button, and
then turn the [Select/Preset] to select a
listening mode.
1 Roll the scroll wheel to select a device for
playback.
Perform this operation when neither the [Mode]
button nor the [Input] button lights. If any button
lights, press it to turn it off.
Rolling the scroll wheel lights both buttons, and
switches the input source and the mode at the
same time.
Phones
Listening Mode Audio Selector Tone Zone 2 Select/ Preset
Push To Enter
Setup Control / Tuning
Push To Enter
Rec/ Zone 3 Digital S Video Video Audio L R Video 7 Input
Level Exit Level Dimmer Memory Tuning
Mode
Clear
Pure Audio Open DVD
Display Tape 1 Tape 2 Tuner Phono C D Net Audio
Video 1 Video 2 Video 3 Video 4 Video 5 Video 6 Video 7
Standby
Master Volume
Rec/ Zone 3 Red ) ( Main Blue ( ) Zone 2 Green ( )
Standby/On
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
Caps Delete Language Loca t ion
Album Ar tist Genre Playlist
Repeat Video Music Photo
@.-'/
--/--- Direct Tuning #
Custom
Display
Dimmer
T V Input
Sleep
Random Main A Main B
Muting
Angle Subtitle Audio
Memory Search A-B Repeat
On Standby T V
T V CH
T V VOL
Exit Gu ide
Rec
Last Memory
Prev CH
Enter
Set up Retu rn
Test Tone CH SEL
Pure A
Surround
Direct
Stereo
Re-EQ
THX All CH ST
Level + Level -
L Night Audio SEL
DSP DSP
+10 0 Clear
1 2 3
4 5 6
7 8 9
Input
To p M enu Men u
VOL CH
Disc
I
+
-
+
-
Zone 3
Zone 2
Input Mode
Macro
Se rve r Aud io A D J
Mode
Select/Preset Listening Mode
Surround
THX
Stereo
ALL CH ST
Input
Direct
Pure A DSP
DSP
Input source buttons
Scroll wheel
RC-556M
2 Start playback on the device you selected
for input.
3 Press the scroll wheel, and then press the
listening mode button you want to select.
Pure A button: To switch the listening mode to
“Pure Audio.” When you select “Pure Audio,” the
video signal is interrupted (resulting in a
blacked-out screen), and the [Pure Audio] indica-
tor lights up.
Direct button: To switch the listening mode to
“Direct.”
Stereo button: To switch the listening mode to
“Stereo.”
Surround button: To switch the listening mode
to the surround mode.
• When 5 channel signals are input, every time
you press the button, the listening mode
changes “DolbyEX”
→ “PLIIx Movie
(Default)” → “PLIIx Music” → “NEO:6” →
“Off”
→
“DolbyEX,” and so on.
• When 2 channel signals are input, every time
you press the button, the listening mode
changes “PLIIx Movie (Default)”
→
“PLIIx
Music”
→
“PLIIx Game”
→
“NEO:6 Cinema”
→
“NEO:6 Music”
→
“PLIIx Movie
(Default),” and so on.
THX button: To switch the listening mode to
“THX.”
• When Dolby Digital multichannel (*/2) signals
are input, you can switch to any of the following
decode modes. Every time you press the button,
the listening mode changes “THX Cinema”
→
“SurroundEX” → “Ultra2 Cinema (Default)” →
“MusicMode” → “Games Mode” → “THX Cin-
ema,” and so on (See page 112).
DSP/DSP buttons: Every time you press
the buttons, you can switch to any of the listening
modes according to the input signals.
ALL CH ST button: To switch the listening
mode to “All Ch Stereo.”
[ ]/[ ] cursor buttons:
• When AAC’s multiplex sound signals are
input, the main-sound and sub-sound are
switched. Every time you press the [
]/[ ]
buttons, the mode changes “Main” → “Sub”
→
“Main + Sub”
→
“Main,” and so on.
• When using the headphones, you can use the
[ ]/[ ] buttons to switch on/off the Dolby
Headphone listening mode.