Marantz SR8002 User Manual
Page 82
79
ENGLISH
OPERATION OF THE MULTI ROOM OUTPUTS
WITH THE REMOTE CONTROL FROM MULTI A
Room A output can be operated from a room
where the unit (SR7002 or SR8002) is not installed.
This requires a separately sold IR receiver. (For
connections, see page 37.)
CHANGE THE MULTI ROOM CONTROL COMMANDS
(RC101) FOR MULTIROOM A
(When operating the unit by Multi Zone connected)
• Zone A: MULTI ROOM A Control (Default)
• Zone B: MULTI ROOM B Control
(The SR7002 does not use this zone.)
Change the control commands for each zone.
2.
1.
1.
Press
SET button and ZONE button until the
SEND indicator blinks twice.
Then
backlight
fl ashes.
2.
Press A zone button.
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF
SOURCE
VOL +/–
MUTE
Tuner mode operation remote code (Refer to page
26)
Notes for the Multi Room System
• If the Tuner (FM or AM) is active in the main room,
you can not control any function of the tuner.In this
case, You must listen to the same station as the main
room.
OSD INFORMATION FOR THE MULTIROOM A SETUP
INFO
Press the INFO button to view the current setup as
shown below on a TV monitor connected to MULTI
VIDEO OUTPUT.
M U L T I R O O M
V I D E O : D S S
A U D I O : D S S
S L E E P : 9 0 m i n
M O N O / S T : S T E R E O
O S D I N F O : E N A B L E
M U L T I : O N M S P K R : O F F
V O L : V A R I V O L : V A R I
L E V E L : - 2 0 d B L E V E L : - 9 0 d B
- - - M A I N R O O M S T A T U S - - -
V I D E O : D V D A U D I O : D V D
OPERATION OF THE MULTI ROOM OUTPUTS
WITH THE REMOTE CONTROL FROM MULTI B
Room B output can be operated from a room
where the unit (SR7002 or SR8002) is not installed.
This requires a separately sold IR receiver. (For
connections, see page 37.)
Note:
The SR7002 does not use MULTIROOM B.
CHANGE THE MULTI ROOM CONTROL COMMANDS
(RC101) FOR MULTIROOM B
Change the control commands for each zone.
2.
1.
1.
Press
SET button and ZONE button until the
SEND indicator blinks twice.
Then
backlight
fl ashes.
2.
Press B zone button.
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF
SOURCE
VOL +/–
MUTE
Tuner mode operation remote code (Refer to page
26)
Notes for the Multi Room System
• If the Tuner (FM or AM) is active in the main room,
you can not control any function of the tuner.In this
case, You must listen to the same station as the main
room.
OPERATION OF THE MULTI SPEAKER
OUTPUTS WITH THE REMOTE CONTROL
To switch to MULTI SPEAKER SYSTEM (A or B)
control, perform the following operations with the
RC101 set to MULTI ROOM A or MULTI ROOM B.
1.
2.
1.
3.
1.
Press
SET button and POWER ON button until
the SEND indicator blinks twice.
Then
backlight
fl ashes.
2.
Press
the
DVD button.
Note
Press the TV button at this time to return to the MULTI
ROOM settings.
3.
Press
ENTER button once to lock in the code.
When the procedure is successful, the SEND
indicator will blink twice.