Marantz SR8002 - Manual (Page 67)

64
ENGLISH
OTHER FUNCTION
DISPLAY MODE
PHONES
AV SURROUND RECEIVER SR8002
M-DAX ENTER MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI T-MODE MEMORY
DISPLAY
EXIT
S
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
L C R SL S SR LFE DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
7
DISP
You can select the display mode for the front display
of the unit.
To select this mode, press the DISPLAY on the
remote controller or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
Input Mode → Surround Mode → Auto display OFF
→ Display OFF → Normal Mode → Input Mode
Normal Mode:
Displays the selected input function. If the function
has been renamed using the Function Rename
feature (see page 44), the renamed name appears
on the display.
Input Mode:
Displays the input mode set via the Function Input
Setup feature (see page 43).
Surround Mode:
Displays the status of the selected surround
mode.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to off
after about 3 seconds. When changing the volume,
it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through this unit is sent to the
record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT, VCR1 OUT, and DSS/VCR2 OUT in
the record mode.
To record the input source signal you are currently
watching or listening to
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
MENU PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
PURE DIRECT
SURROUND SPEAKE MULTI
DSD
POWER ON/OFF
DISP MULTI AUTO TUNED SLEEP SURR DIRECT AUTO
1.
DSS
AMP AUX2 AUX1 TAPE
TUNER CD CD-R MD
VCR DVD TV
1 2 LIGHT
Learning Remote Controller RC8001SR
TAPE
DSS
AUX2 AUX1
TUNER CD CD-R MD
VCR DVD TV
1.
1. Select the input source to record by turning the
INPUT FUNCTION SELECTOR knob on the
front panel or simply press the input selector
buttons on the remote controller.
The input source is now selected and you may
watch or listen to it as desired.
2. The currently selected input source signal
is output to the TAPE OUT, CD/CDR OUT,
VCR1 OUT, and DSS/VCR2 OUT outputs for
recording.
3. Start recording to the recording component as
desired.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
AMP AUX2 AUX1 TAPE
TUNER CD CD-R MD
1 2 LIGHT
Learning Remote Controller RC8001SR
AMP
D4
D5
D2
M
D1
D3
D5
VOL CH
USE PAGE 4
D3
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the > button until
PAGE4 is displayed. Press the A/D (D3) button.
When this button is pressed, the input mode is
switched in the following sequence.
Auto → HDMI → Digital → Analog → Auto
Auto mode:
The types of signals being input to the digital and
analog input jacks for the selected input source are
detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
When “HDMI AUDIO” under PREFERENCE of the
SETUP MENU is set to “THROUGH”, the HDMI
mode cannot be selected.
Digital mode:
The input signal is fi xed to an assigned digital input
terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select “1. INPUT
SETUP” from the MAIN MENU. (See page 43)
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the unit’s output
through a pair of headphones. Be certain that the
headphones have a standard 1/4” stereo phono
plug.
Note that the speakers will automatically be turned
off when the headphone jack is in use.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/OFF
DISP MULTI AUTO TUNED ST SP SLEEP SURR DIRECT AUTO DISC 6.1
Note:
• When using headphones, the surround mode will
change to STEREO and Dolby Headphone by
MENU and Cursor button.
• The surround mode returns to the previous setting
as soon as the headphone plug is removed from the
jack.