MITSUBISHI ELECTRIC WD-65735 - Manual (Page 34)

66 Appendices Appendices 67
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Move the slide switch at the top of the remote to 1.
the position for the product you want to control.
Refer to the table below. Only one of each device
type can be controlled in each slide-switch position.
Switch Position Affected Device
CABLE/SAT Cable Box
DTV Receiver
Satellite Receiver
VCR VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO A/V Receiver
Audio Amplifier
CD Player
Press and hold
2. POWER on the remote control for
several seconds until the button blinks twice and
goes off.
Release the
3. POWER button.
Enter the first five-digit code listed for your equip- 4.
ment.
The • POWER button blinks twice when you start to
enter the code and then once for each addi-
tional keypress.
The • POWER button blinks twice when you finish
entering a valid code.
Move the slide switch to another position if you
•
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
5.
press POWER. If the product has no power on/off
function, press a different key, such as (PLAY),
(STOP), VOL , or MUTE.
If the equipment responds, the remote control •
is properly programmed to operate the equip-
ment.
If the equipment does not respond, repeat
•
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Switch Position Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
Move the slide switch to the position you wish to
1.
verify.
Press and hold
2.
POWER on the remote control for
several seconds until the button blinks twice and
goes off.
Press keys
3. 9 9 0
Press
4. 1 and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
5.
digits of the code.
Audio Lock: Universal A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.
Program the 1. AUDIO position for your A/V receiver as
described earlier in this section.
With the slide switch in the
2. AUDIO position, press
and hold POWER on the remote control for several
seconds until the button blinks twice and goes off.
Press keys
3. 9 9 3 ENTER
The POWER button will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Press and hold
1.
POWER for several seconds until the
key blinks twice and goes off.
2. Press keys
2.
9 9 3 VOL .
The POWER key will blink four times to indicate Audio
Lock has cleared.
Appendix C: Programming the Remote Control, continued
Programming Codes
Audio Amplifiers
Make Code
Acurus 30765
Adcom 31100, 30577
Altec Lansing 31742
Aragon 30765
Bel Canto Design 31583
Bose 30674
Carver 30892
Cary Audio
Design 31879
Classe 31461
Curtis Mathes 30300
Durabrand 31561
Flextronics 31879
GE 30078
Halcro 31934
Harman/Kardon 30892
JVC 30331
Klipsch 30765
Krell 31837
Left Coast 30892
Lenoxx 31561
Lexicon 31802, 31145
Marantz 30892
Mark Levinson 31483
McIntosh 30251
Modulaire 30395
Mondial 30765
Optimus 30823, 30395, 30300,
30013
Parasound 31934
Philips 30892
Pioneer 30823, 30300, 30013
Polk Audio 30892
Primare 31395
RadioShack 30395
RCA 30823, 30300, 30013
Realistic 30013, 30395
Soundesign 30078
Technics 30372
Victor 30331
Wards 30078, 30013
Yamaha 30354
Cable Boxes
Make Code
A-Mark 10144, 10008
ABC 10237, 10014, 10011,
10008, 10007, 10003
Accuphase 10014, 10011, 10007,
10003
Acorn 10237
Action 10237
Active 10237
Americast 10899
Archer 10237
BCC 10276
Bell & Howell 10014
Bell South 10899
British Telecom 10003
Century 10008
Clearmaster 10883
Cable Boxes
Make Code
ClearMax 10883
Comtronics 10040
Cool Box 10883
Coolmax 10883
Digeo 11187
Digi 10637
Director 10476
Dumont 10637
Emerson 10014
Everquest 10040
Fosgate 10276
GC Electronics 10040
GE 10144
General Instru-
ment 10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
Gibralter 10003
GMI 10883
GoldStar 10144, 10040
Hamlin 10273, 10259, 10020
Hitachi 10011, 10008, 10003
Houston 10011
Hytek 10007
Hytex 10007
Insight 10476, 10810
Jebsee 10014
Jerrold 10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
Memorex 10000
Mitsubishi 10003
Motorola 11376, 11254, 11187,
11106, 10810, 10476,
10276, 10014
Multitech 10883
Nova Vision 10008
Novaplex 10008
NSC 10637, 10012
Oak 10007
Pace 11877, 10877, 10237,
10008
Panasonic 10144, 10107, 10008,
10000
Panther 10637
Paragon 10525, 10008, 10000
Penney 10637, 10000
Philips 11305, 10317, 10259
Pioneer 11877, 10877, 10533,
10144
Prism 10012
Pulsar 10040, 10000
Pulser 10040
Quasar 10000
R-Line 10040
RadioShack 10883
RCA 11256
Regal 10279, 10276, 10273,
10259, 10020
Regency 10020
Rembrandt 10040, 10011
Runco 10000
Cable Boxes
Make Code
Samsung 10144, 10040, 10003
Scientific Atlanta 11877, 10877, 10477,
10237, 10012, 10008,
10003, 10000
Signal 10040, 10011
Signature 10011
SL Marx 10040
Sony 11006
Sprucer 10144
Starcom 10014, 10003
Stargate 10040, 10014
Storm 10637
Supercable 10276
Supermax 10883
Teleavia 10040
Teleview 10040
Thomson 11256
Timeless 10040
Tocom 10012
Torx 10003
Toshiba 10000
Tristar 10883
TV86 10040
United Artists 10007
United Cable 10276, 10014, 10011,
10003
US Electronics 10276, 10008, 10003
V2 10883
Videoway 10000
Viewmaster 10883
Vision 10883
Vortex View 10883
Zenith 10899, 10525, 10000
CD Players
Make Code
Acoustic
Research 30420
Aiwa 30157
Akai 30083
Arcam 30157
Audio Pro 30437
Audio Research 30157
Burmester 30420
Cairn 30157
California Audio
Labs 30303, 30029
Cambridge
Soundworks 30157
Carver 30437, 30179, 30157
Cary Audio
Design 31876
Classic 31297
Curtis Mathes 30032
Denon 30766, 30034, 30003
DKK 30000
DMX Electronics 30157
Fisher 31325, 30179, 30000
Garrard 30420
Genexxa 30032
GPX 31296
Appendix C: Programming the Remote Control, continued