Set the, Video switching via hdmi as described on this page, Press – MITSUBISHI ELECTRIC WD-65735 User Manual

Page 31

6. NetCommand IR Control (736 and 835 Series TVs)

Before You Begin

To complete these steps you will need:

The remote controls for both the TV and the

•

A/V receiver.
The IR emitter cable supplied with the TV.

•

An HDMI-to-HDMI cable to connect the A/V

•

receiver to the TV and cables necessary to
connect devices to the A/V receiver.

Connect your audio/video devices to the A/V

receiver. Note the name of the A/V receiver input
used for each device. This information will be
needed later to set up NetCommand’s automatic
input switching.
Connect the A/V receiver to the TV with an HDMI-

to-HDMI cable.
Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 52.
Power on the A/V receiver.

Set the

TV’s remote control slide switch to the TV

position and power on the TV if needed.
When the

Auto Input Sensing screen displays,

select device name

AVR.

Setup to Control A/V Receiver Power and Volume
If you want NetCommand control over the A/V receiv-
er’s power and volume functions, perform the steps
under “A/V Receiver Control: Power and Volume,”
page 57.

Setup to Control TV Audio Output
If your A/V receiver is connected to the TV’s

AVR AUDIO

OUTPUT or DIGITAL AUDIO OUTPUT jacks, set up Net-
Command to control switching to the TV audio input.
Perform the steps under “Setup 1: Automatic A/V
Receiver Switching to the TV Audio Input,” page 58.

A/V Receiver Control: Automatic Video and
Audio Switching via HDMI

If your A/V receiver has an HDMI output, you can use
this procedure to set up control of the A/V receiver’s
audio and video switching. The HDMI connection
allows you to route video signals from multiple devices
over a single cable to the TV. See the diagram below.
The connected devices can be analog, digital, or a
mixture or the two.

Note: If your HDMI A/V receiver has CEC capabilities,

you may be able to fully or partially control your
equipment without performing NetCommand IR
setup.

HDMI

GLASSES

EMITTER

AVR

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

(480i / 480p / 720p / 1080i)

DVI/PC

INPUT

VIDEO

AUDIO

Y/ VIDEO

VIDEO: 480i/480p/720p/1080i/1080p

AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA,

XGA, W-XGA, SXGA, 720p/ 1080p

HDMI

IR-NetCommand

Output / External

Controller Input

INPUT

INP

S-VIDEO

INPUT 3

AUDIO

ANT 2 / AUX

ANT 1 / MAIN

HDMI

)%.*065

)JHIEFmOJUJPO

%7%QMBZFS

$BCMFCPY

7$3

57CBDLQBOFM

"7SFDFJWFSXJUI

)%.*PVUQVU

You can connect
multiple video
devices to an A/V
receiver that has
an HDMI output.

Setting Up NetCommand Control of
an A/V Receiver, continued

Guide to the Inputs > AV Receiver menu for an A/V
receiver with HDMI output

1 The Learn column lists “learnable” keys from the

A/V receiver’s remote control.

2 Input1 through Input5 are arbitrary names used

by the TV to uniquely identify “learnable” A/V
receiver inputs.

3 A check mark next to a key name indicates it has

been “learned” by NetCommand.

4 The Assign Input column provides a list of

possible device types. Use this list to assign the
name of the device type connected to the associ-
ated A/V receiver input. The assigned device
name will appear in the

Input Selection menu.

Setup to Control Automatic Video
and Audio Switching via HDMI
Follow these steps if you wish NetCommand to control
switching of A/V receiver video as well as audio inputs.
When this setup is complete, you can use the TV’s
Input Selection menu to select a video device con-
nected to the A/V receiver. You can also perform addi-
tional NetCommand setup to control devices connected
to the A/V receiver.

Display the

Inputs > AV Receiver menu.

Note: The labels Input1 through Input5 in the Learn

column are arbitrary names used by the TV to
distinguish between A/V receiver inputs.

With the highlight in the

Learn column, highlight

one of the

Input labels (Input1 through Input5).

Press

ENTER and the highlighted Input label will start

flashing to indicate readiness for “learning.”
While the

Input text is flashing, press and hold the

key on the

A/V receiver’s remote control for the

input you wish to associate with the selected

Input

label.
When a check appears next to the

Input label,

release the remote control key.
• If the text stops flashing before the check mark

appears, repeat this step.

• To erase the IR code just “learned,” press

CANCEL

while the name is highlighted.

On the

TV’s remote control, press once. The

highlight will move automatically to the associ-
ated

Assign Input column (Assign Input1 through

Assign Input5).

Setting Up NetCommand Control of
an A/V Receiver, continued

Use

to highlight the device type connected to

the A/V receiver input just “learned.” The

Assign

Input column contains a list of possible device
types.
In the example above, a DVD player is connected to
the A/V receiver input the TV knows as

Input1.

The device type you select here will appear as an
icon in the TV’s

Input Selection menu. You can

assign each device type in the list only once.
Press

EXIT if finished or repeat these steps for addi-

tional video sources connected to the A/V receiver.

NetCommand IR Control of a Device Connected
to an A/V Receiver with HDMI Output
Use this setup if you wish to have NetCommand control
a device sending audio and video through the A/V
receiver to the TV via HDMI.

Note: If your A/V receiver and the connected device

have CEC capability, you may be able to par-
tially operate the device using the TV’s remote
control without any special setup. In that case,
use this procedure to add commands not avail-
able with CEC.

Set up NetCommand control of A/V receiver audio/

video switching via HDMI as described on this
page.

Source Device

A/V Receiver

Any type of

audio/video

connection

HDMI

cable from

TV to A/V

receiver

Press

EXIT to close any open menus and return to

normal TV viewing.
Press

INPUT to open the Input Selection menu.

Highlight the icon for an A/V receiver input

assigned in “Setup to Control Automatic Video and
Audio Switching via HDMI” on this page .
Press

ENTER to switch the TV to the A/V receiver and

the A/V receiver to the device.
Open the

Inputs > Learn menu.

Perform NetCommand “learning” for the device by

following the steps in “Initial NetCommand Setup
for Most Devices,” page 53.