Fostex D1624 - Manual (Page 111)

111
D824/D1624 Reference Manual (Changing the Initial Settings )
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
3.Use the SHUTTLE dial to move the flashing cursor,
and turn the JOG dial to enter the desired offset
value.
For example, if you rotate the JOG dial on the seconds
digit up 59, turning the dial further will increase the
number on the digit of minute by one.
4.Press the EXECUTE/YES key.
The selected offset value is stored and the display returns
to the indication with the flashing [?] that appeared in
step 2.
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
For example, if you set MTC Offset mode to [ABS] (see
the next section) and you wish to start the song from
MTC’s 01h 00m 00s 00f, you may wish to set a preroll
of three seconds with an MTC offset of 00h 59m 57s
00f.
Setting Offset mode (“Offset Mode ?” menu)
If you have selected [MTC] in the “Setting Offset mode” menu, you need to select MTC Offset mode.
This menu enables you to determine whether the specified MTC is output at ABS 00h 00m 00s 00f or at
001bar 1beat 00clk (bar/beat) of the Tempo Map.
* As an example, if you set MTC Offset mode to [ABS] and you wish to start the song from MTC’s 1h 00m 00s
00f, you may want to set a preroll of three seconds with MTC offset of 00h 59m 57s 00f.
If you select [BAR ] as the MTC Offset mode, a preroll of two measures is automatically set. Use 01h 00m 00s
00f; do not set a preroll value.
* If you set Offset mode to [BAR ] and use MTC to synchronize sequence software on the computer, the tempo
of the sequencer may sometimes slip gradually. This is because the tempo of the recorder and the tempo of
the software are slightly different even if both use the same tempo. Some sequence software can read the
tempo output from the recorder correctly. We recommend that you use the tempo of the recorder on the
sequence software. No such problems will occur if the sequence software synchronizes the recorder via MIDI
clock, instead of MTC.
• Initial setting: [ABS]
• Offset mode option: [ABS], or [Bar ]
* You can set the mode for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
Flashing
Setting MTC Offset mode
1.While the recorder is stopped, press the SETUP
key to enter SETUP mode.
2.Turn the JOG dial to select [Offset Mode (?)] ([?]
flashes.), then press the EXECUTE/YES key.
The current offset mode appears on the display.
Pressing the EXECUTE/YES key to turn off the flashing
[?] character. The Offset mode indicator flashes.
With the initial setting, [ABS] flashes as shown below.
3.Use the JOG dial to select the desired Offset mode.
Rotating the JOG dial clockwise or counter-clockwise will
alternately show a flashing [ABS] and
[Bar ].
If you select [ABS], the specified MTC offset time is output
at ABS 00h 00m 00s 00f.
If you select [Bar ], the specified MTC offset time is
output at 001bar 1beat 00clk of the Tempo Map.
4.Press the EXECUTE/YES key.
The selected offset mode is stored and the display returns
to the indication with flashing [?].
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.