Sony VCT-SP2BP Camcorder Shoulder Support - Manual (Page 37)

37
• NFC communication lasts approximately 20
seconds. Perform step 6 within 20 seconds of
performing step 5 . If more than 20 seconds have
elapsed, a confirmation display appears prompting
whether to start NFC communication. Restart the
NFC communication.
• During NFC communication, the signal from the
configured tuner’s wireless microphone cannot be
received.
When SYNC MODE is set to IR
Press and hold the SET button on the transmitter and
press and hold the POWER button for one second to
turn the power on.
When the power is on, place the infrared transmission
port of this unit and the infrared receptor of the
transmitter in close proximity.
Information about the channel set on the unit is sent
to the transmitter, and a prompt appears on the
transmitter display asking if you want to change to
that frequency.
Press the + or – button to select YES, then press the
SET button on the transmitter. The transmit channel
and compander mode are set.
• When SYNC MODE is set to NFC, infrared
communication is not possible.
For details about how to set SYNC MODE, see
“Configuring using communication with the
transmitter (SYNC MODE)” (page 35)
.
• Infrared communication lasts approximately 10
seconds. Perform step 6 within 10 seconds of
performing step 5 . If more than 10 seconds have
elapsed, a confirmation display appears prompting
whether to start infrared communication. Restart
the infrared communication.
Reflecting transmitter settings on the
tuner via NFC communication (SYNC TX-
>RX1(2))
Accesses the frequency and compander mode set on the
transmitter and reflects those settings on the tuner using
NFC communication.
1
Press the + or – button to display the SYNC TX->RX
menu.
2
Press and hold the SET button for one second or
longer.
A confirmation screen appears.
3
Press the + or – button to select YES, then press the
SET button.
4
Place the N-Marks of both the tuner and transmitter in
close proximity (approximately 5 mm).
At this time, make sure that the transmitter is turned
on or that the battery level is sufficient and the
transmitter is turned off.
The frequency and compander mode for use on the
tuner are set.
• NFC communication lasts approximately 20
seconds. Perform step 4 within 20 seconds of
performing step 3 . If more than 20 seconds have
elapsed, a confirmation display appears prompting
whether to start NFC communication. Restart the
NFC communication.
• During NFC communication, the signal from the
configured tuner’s wireless microphone cannot be
received.
• When SYNC MODE is set to IR, the menu is not
displayed and the function cannot be used.
For details about SYNC MODE, see “Configuring
using communication with the transmitter (SYNC
MODE)” (page 35)
.
Switching to the previous channel (CH
MEMORY)
You can switch to the previously set channel. This is
useful when using one tuner in combination with two
transmitters.
Set the channel you want to use beforehand.
For details about how to set a channel, see “Setting the
receive channel” (page 27).
1
Press the + or – button to display the CH MEMORY
menu.
2
Press and hold the SET button until “YES?” starts
flashing.
3
Press the SET button.
The previously set channel and the currently set
channel are displayed. Press the + or – button to
toggle between the channels.
To exit the CH MEMORY function
1
Press and hold the SET button until “CANCEL?” is
displayed.
2
Press the + or – button to display “YES,” and press
the SET button.
The display returns to the CH MEMORY menu.
• If this function is enabled with the factory default
channel settings, two factory default channels are
displayed.
• The NFC SYNC button is disabled while using this
function. Disable this function first if you want to
use the NFC SYNC button.
• When BAND is changed, the default channel in the
new band is stored as the previously set channel.
Notes
Notes
Notes