Powerfix ALUMINIUM INSECT SCREEN BLIND User Manual

Aluminium insect screen blind, Alu szúnyoghálós ablakroló, Ochranná roleta proti hmyzu v hliníkovém rámu

Note: If your window has no outside ledge, to obtain optimal sealing, prior to mounting
the end parts of the handle bars, pull out

the brush seal

10a

at the bottom of the handle

bar

and push it into the lateral nut in the handle bar, designed for this purpose

on the

side facing the window (Detailed image fig. R).

Step 9
Subtract 2 mm from the measured height (H) and transfer this measurement to the guide
channels

Step 10
Using a iron saw, cut the guide channels

to the correct length and polish the sawn edge

with a file (see fig. H).

Follow steps 11 and 12 in the chapter “Installation in the window reveal“.

Step 13
Mount the cover

and a roller blind cassette holder

with a screw

to the roller blind

cassette

. Mount the second roller screen cassette holder

likewise using a screw

the other side of the roller screen cassette

(see fig. R).

Step 14
Mount the guide channel holder

below to the locking parts

(see fig. S).

Step 15
Screw the roller screen cassette

using the screws

14b

through the roller screen cassette

frontally to the wall, in front of the window reveal. Mount the roller screen cassette

such a way that the handle bar

is visible in the window reveal and you are able to grasp

into the handle recesses

to operate the roller screen.

Attention: Use a spirit level for

the installation (see fig. T).
Step 16
Insert the guide channels

into the corresponding latches of the cover

, push them

up as far as they will go to ensure that the guide channels

will be seated at the point of

impact between the covers

of the roller screen cassette

and mount firmly to the

wall using screws

14b

though the guide channel holders

. Ensure that the screw hooks

in the locking parts

are facing the window (see fig. T).

Attention: Use a spirit level for

the installation.

Follow steps 17 and 18 in the chapter “Installation in the window reveal“.
Note: If the wall texture prohibits optimum locking of the guide channels

with the sur-

face of the wall, the guide channels can each be mounted

using a screw

to the wall.

To achieve this purpose, define a drilling point approx. in the middle of the guide channels

and drill a hole through the profile panels with a 4 mm drill (see fig. T). Remove the guide
channels

, insert the dowel plugs and remount the guide channels

. Now drill holes

that are visible in the outer frames of the profile using an 8 mm drill (size of the screw head).
Mount the guide channels

using the screws

to the wall through the holes. Seal the

8 mm drill holes with the caps

(see fig. T).

Installation outside the window reveal in windows

with window ledges

If the window is equipped with a window ledge, the guide channel holders cannot be
mounted

. Place the guide channels

on the window ledge. Define a drilling point A

Step 16
Stick the double-sided adhesive tape

approx. 2 cm from the bottom edge, to which the

locking parts

are attached, to the guide channels

. Remove the protective foil (see

detail 1, fig. N). Insert the guide channels

left and right into the respective latch of the

cover

and align by pushing them up into the latches of the cover

in the win-

dow reveal (fig. N).

Attention: The screw hooks

of the locking parts

must be facing

towards the window (see detailed image 2, fig. N). Ensure that the guide channels

are

correctly aligned, this means that the the back of the roller blind

and the rear sides of the

guide channels

form one surface and therefore exhibit a uniform clearance to the outer

edge of the wall. You can now press the guide channels

firmly to the wall reveal to

adhere them into place (see fig. N).

Alternative screw assembly: Alternatively, the

guide channels

can also be screw mounted by applying to each guide channel

two

screws

at an equal distance to mount the guide channels

to the window reveal. Pro-

cure dowel plugs matching the screws included in the delivery according to the structure of
the wall. Using a 4 mm drill, drill a hole through the rear profile of the guide channels posi-
tioned in the reveal

(Detailed image, fig. O), in this way you will obtain the corresponding

marking on the window reveal. Now remove the guide channels

from the reveal, insert

the matching dowel plugs into the reveal at the markings and screw the guide channels

following renewed insertion into the latches of the cover

with the screws

through

the drilled holes on the reveal (see fig. O).
Step 17
Pull down the roller screen and hook the handle bar

into the screw-in hooks

of the

locking parts

. To accomplish this, pull down the handle bar

, tilt it towards your body

and allow the handle bar to snap into place

into the screw-in hooks

(see fig. Q1).

Note: If the roller screen does not snap into place immediately, keep the handle bar
pressed down

while you continue to screw down the screw-in hooks

in the direction

of the handle bar

(see fig. P).

Attention: In any case, hold the handle bar

firmly

until correct hooking in has been achieved to prevent the roller screen from springing back.
In this way you can now correct potential level differences between the bush and the wall
by turning the screw-in hooks downwards while the roller blind is closed. Do not screw too
far down to avoid bending the bush seal in the handle bar

which would impair the sealing.

Step 18
To open the roller blind, press down the handle bar

and then tilt it outwards away from

your body to unhook it. Allow the fibre glass fabric to slowly roll back into the roller blind
cassette (see fig. Q2).

Alternative option of installation on the wall, in front

of the window reveal

If you have no possibility of installing the roller blind in your window reveal, you can mount
it on the wall, in front of the reveal.

Step 1
Measure the height (H) and width (W) of your window reveal (see fig. A).
Step 2
Add 72 mm to the measured width (W) and transfer the resulting dimensions to the measuring
tape of the roller blind cassette

Follow steps 3 to 8 in the chapter “Installation in the window reveal“.

Step 2
Remove the self-adhesive bush seal

from the inside of the handle bar

(see fig. B).

Step 3
Transfer the dimensions of the measured width (B) to the measuring tape of the roller blind
cassette

Note: The cassette

can be shortened to maximum 70 cm, regardless of the

printed measuring tape length. Draw out the fibre glass fabric

a little and wrap it round

the roller blind cassette

, ensuring that the fabric

cannot return to the cassette

. If

necessary, have a second person help you with the installation. Ensure that the roller blind
cassette

, the fibre glass fabric

and the handle bar

form one surface (see fig. C).

Step 4
Now saw through the roller blind cassette

, the fibre glass fabric

and the handle bar

with an iron saw (see fig. C).

Note: Use a mitre box for this purpose.

Step 5
Polish the interface with a file and remove the aluminium filings with a paint brush.
Step 6
Fix the cover

to the interface of the roller blind cassette

with a screw

14a

(see fig. D).

Step 7
Slide one of the handle recesses first

, then the cord

and finally the second handle

recess

into the slot provided for that purpose

(see fig. E).

Step 8
Place the end caps

left and right onto the handle bar

(see fig. F).

Step 9
Stick the self-adhesive bush seal

centred to the ceiling side of the roller screen cassette

(see fig. G) and cut off the protruding end.

Note: This step can be omitted in the case of

installation outside the reveal.
Step 10
Subtract 46 mm from the measured height (H) and transfer this measurement to the two
guide channels

. Using a iron saw, cut the guide channels

to the correct length (see

fig.H).

Note: Use a mitre box for this purpose. Then remove any burrs from the sawn edges

using a file.
Step 11
Using pliers, clamp the brush seal carrier at the lower end of the guide channels

together

with the integrated bush seal. In this way you will prevent the bush from sliding out during
application (see fig. I).
Step 12
Screw one retaining hook

into each of the locking parts

and attach the locking parts

together with the retaining hooks

to the bottom of the two guide channels

(see fig. J).

Step 13
Attach the two bow springs

to the sealing cover

(see fig. K).

Note: This step can be

omitted in the case of installation outside the reveal.
Step 14
Attach the two bow springs

to the sealing cover

and position this together with the

spiral spring

on the roller screen cassette

(see fig. L). Keep this firmly pressed to the

cassette

Step 15
Keeping the cover

firmly pressed to the roller screen cassette

, clamp the cassette

into the wall reveal (see fig. M).

Attention: Ensure that the roller blind cassette

is cor-

rectly mounted, this means a uniform clearance to the outer edge of the wall throughout the
entire width.

1 Roller blind cassette
1 Fibreglass fabric
1 Handle bar
2 Guide channels
2 Cover
2 Handle recesses
1 Pull cord
2 Handle bar end parts
2 Locking parts
2 Screw hooks
4 Bow springs
1 Spiral spring
1 Brush seal, self-adhesive
1 Brush seal handle bar
2 Double-sided adhesive tapes
2 Guide channel holders
2 Roller blind cassette holders
9 Screws
4 Caps
1 Installation instructions

Safety advice

RISK OF FATAL INJURY AND RISK OF ACCIDENT

FOR INFANTS AND CHILDREN! Never leave children unattended with
the packaging material or the product. There is a risk of suffocation from the

packaging materials and a risk of fatal injury by strangulation. Children often underestimate
dangers. Please keep children away from the device at all times. The product is not a toy.

DANGER TO LIFE! Do not lean too far out of the window when you

are installing, removing or cleaning the product.

CAUTION! RISK OF INJURY! Please ensure that no parts are damaged and that
all parts are correctly assembled. Risk of injury exists if assembled incorrectly. Damaged
parts can effect safety and function.

Installation in the window reveal

Check before installation that your window reveal is suitable for this product and does

not exceed the maximum permissible dimensions. The depth of the reveal must not be
less than 5 cm. If necessary, have a second person help you with the installation.

Note: If your window opens outwardly, you can also mount the roller blind to the inside of
the window or to the reveal.

Step 1
Measure the height (H) and width (B) of your window reveal (see Fig. A).
Attention: Take into account any differences in length between the left and right windows,
as the window reveal is not always equal, especially in older buildings.

Aluminium Insect Screen Blind

Introduction

Familiarise yourself with the product prior to assembly. Carefully read the follow-
ing assembly instructions and safety tips. Only use the product as described and
for the specified applications. Keep the instructions in a safe place, you might

need them later. If passing this product on to a third party also include all documents.

Proper use

This article is designed to provide protection against insects such as flies and is intended for
indoor use only. Any use other than previously mentioned or any product modification is
prohibited and can lead to injuries and / or product damage. The manufacturer is not liable
for any damages caused by any use other than for the intended purpose. The product is not
intended for commercial use.

Description of parts and features

Roller blind cassette

Fibre glass fabric

Handle bar

Guide channel

Cover

Handle recess

Pull cord

Handle bar end part

End part

Screw-in hook

Bow spring

Spiral spring

Brush seal, self-adhesive

10a

Brush seal handle bar

Double-sided adhesive tape

Guide channel holder

Roller blind cassette holder

Round head screw

14a

Flat head screw

14b

Round head screw long

Cover caps

Technical data

Max. dimensions of window reveal: 130 x 160 mm (W x H)

Included items

Note: When opening the packaging, please make sure not to accidentally throw away
assembly materials. Please check immediately on unpacking that the delivery is complete
and that the product and all parts are in perfect condition. Do not under any circumstances
assemble the product if the delivery is incomplete.

14a

10a

14b

You need · Potrzebujecie · Szüksége van

Potrebujete · Potřebujete · Budete potrebovať · Sie benötigen:

ALUmINIUm INSECT SCREEN BLIND

Assembly and safety advice

ALU SzúNYOGHáLóS ABLAKROLó

Használati- és biztonsági utasítások

OCHRANNá ROLETA PROTI HmYzU v

HLINíKOvém RámU

Pokyny k montáži a bezpečnostní pokyny

ALU-INSEKTENSCHUTz-FENSTERROLLO

Montage- und Sicherheitshinweise

ROLETA ALUmINIOwA CHRONIąCA

PRzED OwADAmI

Wskazówki dotyczące montażu oraz

bezpieczeństwa

ALUmINIJASTI OKENSKI ROLO zA

zAščITO PRED mRčESOm

Navodila za montažo in varnost

HLINíKOvá, PROTIHmYzOvá

OKENNá ROLETA

Pokyny pre montáž a bezpečnosť

14a

14b

1 x

2 x

1 x

2 x

1 x

2 x

6 x

1 x

2 x

4 x

1 x

4 x

1 x

2 x

10a

1 x