Yaskawa AC Drive Z1000 Bypass Technical Manual User Manual
Page 458
T1-07 ....................................................................... 113, 114
TdE ............................................................................... 236
Terminal A1 Bias Setting...................................................... 161
Terminal A1 Function Selection.............................................. 161
Terminal A1 Gain Setting ..................................................... 161
Terminal A1 Signal Level Selection ......................................... 160
Terminal A2 Bias Setting...................................................... 162
Terminal A2 Function Selection.............................................. 162
Terminal A2 Gain Setting ..................................................... 162
Terminal A2 Signal Level Selection ......................................... 162
Terminal Block Configuration ..................................................60
Terminal Board Connection Error............................................ 225
Terminal TB1 .....................................................................36
Terminal TB2 .....................................................................36
Terminal TB3 ................................................................ 35, 36
Terminal TB4 .....................................................................35
Test Run.................................................................... 111, 114
Through Mode .................................................................. 157
TIM ............................................................................... 236
Time Data Error................................................................. 236
Time Not Set .................................................................... 236
Time to Continue Making Fault Restarts .................................... 325
Too Many Speed Search Restarts............................................. 236
Torque Compensation Gain ............................................. 140, 220
Torque Compensation Primary Delay Time ................................ 220
Torque Detection ............................................................... 164
Torque Detection 1 ............................................................. 157
Torque Detection Level 1................................................ 178, 326
Torque Detection Selection 1 ........................................... 177, 326
Torque Detection Time 1 ................................................ 178, 326
Troubleshooting without Fault Display...................................... 253
TrPC .............................................................................. 244
Tuning Errors.................................................................... 221
Types of Alarms, Faults, and Errors ......................................... 221
Types of Auto-Tuning for Induction Motors................................ 111
U
U/T1 ................................................................................62
U1-01 ............................................................................. 256
U1-07 ............................................................................. 254
U2-oo, U3-oo, and UB-oo Initialization ..................................... 184
UL3 ......................................................................... 236, 244
UL6 ......................................................................... 237, 244
UL and CSA Standards ........................................................ 439
UL Standards Compliance.......................................................62
Undertorque Detection 1................................................. 236, 244
Undertorque Detection 6....................................................... 244
Undertorque Detection Operation ............................................ 177
Undervoltage .................................................................... 244
Undervoltage 3 .................................................................. 237
Undervoltage 3 (Soft-Charge Circuit Fault)................................. 237
Undervoltage Detection Level (Uv1) .................................. 170, 324
Undervoltage Protection ....................................................... 300
Unexpected Noise from Connected Machinery............................. 257
Unit Code ........................................................................ 184
Up/Down Command Operation............................................... 152
Up Arrow Key.....................................................................92
User-Set Display Units Decimal Display.................................... 184
User-Set Display Units Maximum Value.................................... 184
User-Set Speed Agree 1........................................................ 155
User-Set Speed Agree 2........................................................ 157
Uv ................................................................................. 244
Uv1 ............................................................................... 237
Uv2 ............................................................................... 237
Uv3 ............................................................................... 237
V
V/f Characteristics .............................................................. 300
V/f Control.........................................................................27
V/f Control Mode Tuning ..................................................... 220
V/f Control Mode Tuning Parameters ....................................... 220
V/f Data Setting Error.......................................................... 247
V/f Gain During Speed Search................................................ 125
V/f Pattern Selection ..................................................... 145, 256
V/T2 ................................................................................62
Verifying Parameter Changes ................................................. 100
Vibration/Shock................................................................. 300
voF .......................................................................... 238, 245
Voltage drop calculation formula...............................................62
Voltage Reduction Rate.................................................. 186, 330
Voltage Restoration Complete Level .................................. 187, 330
Voltage Restoration Level ............................................... 186, 330
Voltage Restoration Sensitivity Time Constant ...................... 187, 330
Voltage Restoration Time Constant at Impact ........................ 187, 330
W
W/T3................................................................................62
Waiting for Run ................................................................. 245
Warranty Information ............................................................23
Watt Hour Pulse Output ....................................................... 160
Watt Loss 200 V Class Three Phase Models................................ 302
Watt Loss 400 V Class Three Phase Models................................ 302
Wiring Distance................................................................. 141
Wiring the Control Circuit Terminal ...........................................80
Writing BACnet Bypass Parameters ......................................... 370
Writing to Multiple Registers ................................................. 387
WrUn ............................................................................. 245
Z
Z: Bypass Parameters .......................................................... 195
Z1000 Bypass Faults with Apogee Configuration ......................... 416
Zero Speed....................................................................... 154
Index
458
YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual