B: application, B1: operation mode selection, B2: dc injection braking and short circuit braking – Yaskawa AC Drive Z1000 Bypass Technical Manual User Manual
Page 310: B3: speed search, B.3 b: application
B.3 b: Application
Application parameters configure the source of the Run command, DC Injection Braking, Speed Search, timer functions, PI
control, Energy Savings, and a variety of other application-related settings.
u
b1: Operation Mode Selection
No.
(Addr.
Hex)
Name
Description
Values
Page
b1-03
(182)
Stopping Method Selection
Stopping Method
0: Ramp to stop
0: Ramp to Stop
1: Coast to stop
1: Coast to Stop
2: DC Injection Braking to stop
2: DCInj to Stop
3: Coast with timer
3: Coast w/Timer
Default: 1
Range: 0 to 3
b1-04
(183)
Reverse Operation Selection
Reverse Oper
0: Reverse enabled
0: Reverse Enabled
1: Reverse disabled
1: Reverse Disabled
Default: 1
Range: 0, 1
u
b2: DC Injection Braking and Short Circuit Braking
No.
(Addr.
Hex)
Name
Description
Values
Page
b2-01
(189)
DC Injection Braking Start
Frequency
DCInj Start Freq
Sets the frequency at which DC Injection Braking starts when “Ramp to stop”
(b1-03 = 0) is selected.
Default: 0.5 Hz
Min.: 0.0
Max.: 10.0
b2-02
(18A)
DC Injection Braking
Current
DCInj Current
Sets the DC Injection Braking current as a percentage of the drive rated current.
Default: 50%
Min.: 0
Max.: 100
b2-03
(18B)
DC Injection Braking Time
at Start
DCInj Time@Start
Sets DC Injection Braking time at start. Disabled when set to 0.00 seconds.
Default: 0.00 s
Min.: 0.00
Max.: 10.00
b2-04
(18C)
DC Injection Braking Time
at Stop
DCInj Time@Stop
Sets DC Injection Braking time at stop.
Default: 0.00 s
Min.: 0.00
Max.: 10.00
u
b3: Speed Search
No.
(Addr
Hex.)
Name
Description
Values
Page
b3-01
(191)
Speed Search Selection at
Start
SpdSrch at Start
0: Disabled
0: Disabled
1: Enabled
1: Enabled
Default: 0
Range: 0, 1
b3-02
(192)
Speed Search Deactivation
Current
SpdSrch DeactCur
Sets the current level at which the speed is assumed to be detected and Speed
Search is ended. Set as a percentage of the drive rated current.
Default: 120%
Min.: 0
Max.: 200
b3-03
(193)
Speed Search Deceleration
Time
SpdSrch Dec Time
Sets output frequency reduction time during Speed Search.
Default: 2.0 s
Min.: 0.1
Max.: 10.0
b3-04
(194)
V/f Gain during Speed
Search
SpdSrch V/f
Determines how much to lower the V/f ratio during Speed Search.
Output voltage during Speed Search equals the V/f setting multiplied by b3-04.
Default:
<1>
Min.: 10%
Max.: 100%
b3-05
(195)
Speed Search Delay Time
Search Delay
When using an external contactor on the output side, b3-05 delays executing
Speed Search after a momentary power loss to allow time for the contactor to
close.
Default: 0.2 s
Min.: 0.0
Max.: 100.0
b3-06
(196)
Output Current 1 during
Speed Search
Srch Im Lvl1
Sets the current injected to the motor at the beginning of Speed Estimation
Speed Search. Set as a coefficient for the motor rated current.
Default:
<1>
Min.: 0.0
Max.: 2.0
b3-07
(197)
Output Current 2 during
Speed Search (Speed
Estimation Type)
Srch Im Lvl2
Sets the amount of output current during Speed Estimation Speed Search as a
coefficient for the no-load current (output current during Speed Search is
automatically limited by the drive rated current).
Increase this setting value in increments of 0.1 if the drive fails to perform
Speed Estimation.
Default: 1.0
Min.: 0.0
Max.: 5.0
B.3 b: Application
310
YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual