Yaskawa P7 Drive User Manual - Manual (Page 248)

Index - 8
RUN Indicator ...................................................................3-5
Running
Signal........................................................................2-23
Stall Prevention during...................................5-42, A-19
S
Scaling Display
Digital Operator .............................................5-52, A-22
PI Setpoint ........................................................5-20, A-7
S-Curve Characteristic
at Accel End ..............................................................A-8
at Accel Start ............................................................ A-8
Search Operation Voltage Limit .......................................A-8
SEQ ...................................................................................3-4
Sequence Parameters ........................................................A-4
Serial Communications ....................................................D-2
Address......................................................................D-4
Baud Rate ...........................................................6-8, D-4
Drive Node Address ..................................................D-4
Parameters .......................................................A-18, D-4
Run Command ...........................................................5-4
Self-Diagnosis Function..........................................D-14
Serial Number ...................................................................1-3
Setpoint (PI Function) .....................................................5-20
Boost Setting ....................................................5-21, A-7
Display Scaling .........................................................A-7
Selection................................................. 5-15, 5-19, A-6
Value.................................................................5-20, A-6
SHIFT/RESET Key...........................................................3-3
Shield Wire Grounding.......................................... 2-21, 2-28
Shipping Damage ..............................................................1-3
Short Circuit Protection, Branch ...............................E-2, E-3
Shunt Connector CN15 ...................................................2-25
Sinking/Sourcing Mode................................................. 2-26
Skip Frequency –– See Jump Frequency and Frequency
Limits ...............................................................5-27, A-9
Slave – See Modbus Communication Configuration .......D-2
Sleep Function – See PI Function, Sleep ................5-19, A-7
Snooze Function – See PI Function, Snooze. 5-21, 5-22, A-7
Soft Charge Contactor
Alarm........................................................................6-10
Checking ..................................................................6-21
Fault............................................................................6-7
Preventive Maintenance .............................................7-3
Soft Charge Resistor
Checking ..................................................................6-21
Preventive Maintenance .............................................7-3
Soft CLA Selection ........................................................ A-21
Soft Start — see S-Curve................................................. A-8
Software Number........................................................... A-26
SPEC .......................................................................... 1-3, 1-4
Specifications....................................................................C-1
Design ........................................................................ 1-4
General.......................................................................C-4
Standard Drive
208-240Vac.........................................................C-2
480Vac ................................................................C-3
Nameplate........................................................... 1-3
Speed
Agreement ...........................................5-46, A-15, A-20
Control Accuracy.......................................................C-4
Range .........................................................................C-4
Speed Command – See also Frequency Reference
0-10Vdc ............................................................ 2-23, 4-9
4-20mA ............................................................. 2-23, 4-9
Limits....................................................................... 5-26
Loss Detection ......................................................... 5-43
Selection ............................................................. 4-6, 5-4
Setting Selection ...................................................... 5-54
Signal Polarity ........................................................... 4-9
Troubleshooting .............................................. 6-15, 6-16
Speed Reference, Multiple (Multi-step Speed Operation) –
See Preset Speeds............................................................. A-9
Speed Search .................................................................. 5-11
Auto-Tuning ........................................................... 5-59
Parameters ................................................................ A-5
Stall Prevention
Parameters ..................................................... 5-40, A-19
Specifications.............................................................C-4
Troubleshooting ....................................................... 6-16
Start-up ...................................................................4-1 to 4-9
Assistance ..........................................Inside Back Cover
Benchmark data ......................................................... 4-8
Preparation for ........................................................... 4-2
Procedure ................................................................... 4-5
Station Address (Modbus Control) ................................. D-5
Stop bits – See Modbus Communications ....................... D-1
STOP Indicator ................................................................ 3-5
Stop Method Selection (OH) ........................................ A-21
Stopping Method ....................................... 4-7, 5-6, 5-7, A-4
Coast to Stop.............................................................. 5-6
Coast w/Timer ........................................................... 5-7
DcInj to Stop.............................................................. 5-7
for External Fault from OPT Card .......................... A-11
Ramp to Stop ............................................................. 5-5
Selection (OH) ......................................................... 5-48