Yaskawa P7 Drive User Manual - Manual (Page 246)

Index - 6
Motor........................................................ 6-5, 6-9, A-18
Parameters .....................................................A-18, A-21
Pre-Alarm.........................................................6-9, A-21
Overload
Alarms/Faults ................................................... 5-45, 6-5
And Auto Restart......................................................5-45
Capacity..................................................................... C-4
Drive................................................................. 5-31, 6-5
Motor................................................................6-5, A-18
Protection ........................................................A-18, C-4
Overtorque – See Torque Detection .....................5-46, A-20
Overvoltage Protection............................. 5-28, 6-6, 6-9, C-4
And Auto Restart......................................................5-45
DC Bus – See DC Bus Voltage .................. 6-6, 6-9, C-4
P
Parameters
Accel/Decel (C1-01 – C1-11) ...................................A-8
Analog Inputs (H3-02 – H3-13) ..............................A-16
Analog Outputs (H4-01 – H4-08) ..........................A-17
Auto-Tuning (T1-02 – T1-04).................................A-24
Capacity Related ....................................................... B-1
Carrier Freq (C6-02 – C6-05) ...................................A-9
Com OPT Setup (F6-01 – F6-05)............................ A-11
COPY Function (o3-01 – o3-02).............................A-24
DC Braking (b2-01 – b2-09) .....................................A-5
Delay timers (b4-01 – b4-02)....................................A-5
Digital Inputs (H1-01 – H1-05)..................A-12 to A-14
Digital Outputs (H2-01 – H2-02)............................A-15
Energy Saving (b8-01 – b8-06).................................A-7
Example of Changing..................................... 3-14, 3-15
Factory Reset (Initialize) ..........................................A-2
Fault Restart (L5-01 – L5-03) .................................A-20
Hdwe Protection (L8-01 – L8-19)...........................A-21
High Slip (n3-01 – n3-04) .......................................A-22
Hunting Prevention (n1-01 – n1-02) .......................A-21
Initialization (A1-00 – A1-05) ..................................A-2
Jump Frequencies (d3-01 – d3-04) ...........................A-9
Key Selections (o2-01 – o2-15) ....................A-23, A-24
Listing of .................................................... A-1 to A-28
Modified .......................................................... 3-6, 3-13
Monitor Select (o1-01 – o1-08).....................A-22, A-23
MOP/Trim Control (d4-01 – d4-02)........................A-10
Motor Overload (L1-01 – L1-05)............................A-18
Motor Setup (E2-01 – E2-05) ................................. A-11
PI Control (b5-01 – b5-30)................................A-6, A-7
Preset Reference (Speeds) (d1-01 – d1-17) ..............A-9
Programming (Basic) .................................... 5-1 to 5-60
PwrLoss Ridethru (L2-01 – L2-05).........................A-19
Ref Detection (L4-01 – L4-06) ...............................A-20
Reference Limits (d2-01 – d2-03) ............................ A-9
S-Curve Acc/Dec (C2-01 – C2-02) .......................... A-8
Sequence (b1-01 – b1-12)......................................... A-4
Serial Com Setup (H5-01 – H5-09) ........................ A-18
Setting and Reading.......................................3-6 to 3-15
Speed Search (b3-01 – b3-14) .................................. A-5
Stall Prevention (L3-01 – L3-06) ........................... A-19
Torque Comp (C4-01 – C4-02)................................. A-8
Torque Detection (L6-01 – L6-03) ......................... A-20
Troubleshooting ....................................................... 6-14
User (A2-01 – A2-32)....................................... A-2, A-3
V/f Pattern (E1-01 – E1-13) ................................... A-10
Parity – See Modbus Communications........................... D-1
Parts ........................................................................................
Ordering Replacement .......................Inside Back Cover
Replacement Guidelines ............................................ 7-4
Password
Setting ....................................................................... A-2
Troubleshooting ....................................................... 6-14
PCB
Control
Inspecting ........................................................... 7-2
Gate Drive
Inspecting ........................................................... 7-2
Power
Inspecting ........................................................... 7-2
Terminal
Inspecting ........................................................... 7-2
Removing and Mounting.................................... 7-6
Peripheral Devices
AC and DC reactor ...................................................E-2
Magnetic Contactor ...................................................E-2
Molded-case circuit breaker (MCCB) .......................E-2
Troubleshooting ....................................................... 6-17
Phase Loss Detection
Input ................................................................ 6-6, A-21
Output ....................................................................... 6-9
Phase-to-Phase Short .......................................... 6-5, 6-9
Physical Installation –See Installation, Physical............... 1-1
PI Feedback Loss .............................................................. 6-4
PI Function
Accel/Decel Time ............................................ 5-19, A-6
Block Diagram......................................................... 5-15
Feedback .....................................................5-15 to 5-18
Differential ....................................5-15, 5-38, A-16
Loss Detection Level................................ 5-18, A-6
Loss Detection Time................................. 5-18, A-6
Reference Missing Detection .................. 5-18, A-6
Square Root Function Activation ............. 5-23, A-6
Integral Limit Setting....................................... 5-17, A-6
Integral Time Setting ....................................... 5-16, A-6