Yaskawa P7 Drive User Manual - Manual (Page 191)

Parameters A - 17
Table 1: Parameter List (Continued )
Parameter
No.
Parameter Name
Digital Operator Display
Description
Setting
Range
Factory
Setting
Menu
Location
Analog Outputs
H4-01
Terminal FM Monitor Selection
Terminal FM Sel
Selects which monitor will be output on terminals FM
and AC.
1: Frequency Ref (100% = max. output frequency)
2: Output Freq (100% = max. output frequency)
3: Output Current (100% = drive rated current)
6: Output Voltage (100% = 230V or 100% = 460V)
7: DC Bus Voltage (100% = 400V or 100% = 800V)
8: Output kWatts (100% = drive rated power)
15: Term A1 Level
16: Term A2 Level
18: Mot SEC Current (100% = Motor rated secondary
current)
20: SFS Output (100% = max. output frequency)
24: PI Feedback
31: Not Used
36: PI Input
37: PI Output (100% = max. output frequency)
38: PI Setpoint
51: Auto Mode Fref (100% = max. output frequency)
52: Hand Mode Fref (100% = max. output frequency)
53: PI Feedback 2
NOTE: 100% = 10V DC output * FM gain setting
(H4-02).
1 to 53 2 Programming
H4-02 Terminal FM Gain Setting
Terminal FM Gain Sets terminal FM output voltage (in percent of 10V)
when selected monitor is at 100% output. 0.0 to
1000.0
100.0% Programming
H4-03 Terminal FM Bias Setting
Terminal FM Bias Sets terminal FM output voltage (in percent of 10V)
when selected monitor is at 0% output. –110.0 to
110.0
0.0% Programming
H4-04
Terminal AM Monitor Selection
Terminal AM Sel
Selects which monitor will be output on terminals AM
and AC.
1: Frequency Ref (100% = max. output frequency)
2: Output Freq (100% = max. output frequency)
3: Output Current (100% = drive rated current)
6: Output Voltage (100% = 230V or 100% = 460V)
7: DC Bus Voltage (100% = 400V or 100% = 800V)
8: Output kWatts (100% = drive rated power)
15: Term A1 Level
16: Term A2 Level
18: Mot SEC Current (100% = Motor rated secondary
current)
20: SFS Output (100% = max. output frequency)
24: PI Feedback
31: Not Used
36: PI Input
37: PI Output (100% = max. output frequency)
38: PI Setpoint
51: Auto Mode Fref (100% = max. output frequency)
52: Hand Mode Fref (100% = max. output frequency)
53: PI Feedback 2
NOTE: 100% = 10V DC output * AM gain setting
(H4-05).
1 to 53 8 Programming
H4-05 Terminal AM Gain Setting
Terminal AM Gain Sets terminal AM output voltage (in percent of 10V)
when selected monitor is at 100% output. 0.0 to
1000.0
50.0% Programming
H4-06 Terminal AM Bias Setting
Terminal AM Bias Sets terminal AM output voltage (in percent of 10V)
when selected monitor is at 0% output. –110.0 to
110.0
0.0% Programming
H4-07
Terminal FM Signal Level
Selection
AO Level Select1
0: 0 - 10 VDC
2: 4-20 mA*
0 or 2 0 Programming
H4-08
Terminal AM Signal Level
Selection
AO Level Select2
0: 0 - 10 VDC
2: 4-20 mA*
* An analog output of 4 - 20 mA can not be used with
the standard terminal board. Therefore an optional
terminal board (with shunt connector CN15) is needed.
0 or 2 0 Programming
Denotes that parameter can be changed when the drive is running.