Yaskawa GPD 506/P5 to F7 - Manual (Page 51)

Appendix 3- Parameter Cross Reference
PL.F7.05 Page 51 of 54
GPD506/P5 Parameter F7 Parameter
Param
No.
Nxxx
Parameter
Name
Description or Selection Description or Selection
Parameter
Name
Param.
No.
081 (timer function)
Off delay time Set unit: 0.1sec
Set range: 0.0-25.5sec 0.0 to 3000.0
Used in conjunction with a multi-function
digital input and a multi-function digital
output programmed for the timer function.
This sets the amount of time the output
stays energized after the digital input is
opened. Timer Function OFF-Delay
Time b4-02
082 Braking resistor
Overheat protection 0: Braking resistor overheat protection
disabled.
1: Braking resistor overheat protection
enabled. Selects the DB protection only when using
3% duty cycle heatsink mount Yaskawa
braking resistor. This parameter does not
enable or disable the DB function of the
Drive.
0: Not Provided
1: Provided Internal Dynamic Braking
Resistor Protection Selection L8-01
083 Input open-phase
detection level Set unit:1% and set range: 1-100%
(Open-phase detection disabled at set point
=100%) Selects the detection of input current phase
loss, power supply voltage imbalance, or
main circuit electrostatic capacitor
deterioration.
0: Disabled
1: Enabled Input Phase Loss Protection
Selection L8-05
084 (PID control)
PID control selection 0: PID control disabled.
1: PID control enabled. (D=Fdbk)
2: PID control enabled. (D=Fdfwd)
3: PID control enabled.
(D=Fdbk, feedback=reverse) This parameter determines the function of
the PID control.
0: Disabled
1: D = Feedback
2: D = Feed-Forward
3: Freq. Ref. + PID output (D = Feedback)
4: Freq. Ref. + PID output
(D = Feed-Forward) PID Function Setting
b5-01
085 (PID control)
Feedback gain Set unit: 0.01
Set range: 0.00-10.00   
086 (PID control)
Proportional gain Set unit: 0.1
Set range: 0.0-10.0 0.00 to25.00
Sets the proportional gain of the PID
controller. Proportional Gain Setting b5-02
087 (PID control)
Integral time Set unit: 0.1sec
Set range: 0.0-100.0sec 0.0 to 360.0
Sets the integral time for the PID
controller. A setting of zero disables
integral control. Intregral Time Setting
b5-03
088 (PID control)
Derivative time Set unit: 0.01sec
Set range: 0.00-1.00sec 0.00 to 10.00
Sets D control derivative time. A setting of
0.00 disables derivative control. Derivative Time b5-05
089 (PID control)
Integration upper limit Set unit: 1%
Set range: 0-109% 0.0 to100.0
Sets the maximum output possible from the
integrator. Set as a% of maximum
frequency. Intregral Limit Setting
b5-04
090 PID Feedback loss
detection selection 0: PID feedback loss disabled.
1: PID feedback loss enabled, no fault
detected.
2: PID feedback loss enabled, fault detection
enabled. 0: Disabled
1: Alarm
2: Fault PID Feedback Reference
Missing Detection Selection b5-12
091 PID Feedback loss
detection level Set unit:1%
Set range: 0-100% 0 to 100
Sets the PID feedback loss detection level
as a percentage of maximum frequency
(E1-04). PID Feedback Loss Detection
Level b5-13
092 PID Feedback loss
detection time Set unit: 0.1sec
Set range: 0.0-25.5sec 0.0 to 25.5
Sets the PID feedback loss detection delay
time in terms of seconds. PID Feedback Loss Detection
Time b5-14
093 PID output
reverse-characteristic 0: Reverse-characteristic disabled
1: Reverse-characteristic enabled. Determines whether the PID controller will
be direct or reverse acting.
0: Normal Output (direct acting)
1: Reverse Output (reverse acting) PID Output Level Selection b5-09
094 PID Sleep function
operation level Set unit: 0.1Hz
Set range: 0.0-400.0Hz 0.0 to 200.0
Sets the sleep function start frequency. Sleep Function Start
Level b5-15
095 PID Sleep function
operation time Set unit: 0.1sec
Set range: 0.0-25.5sec 0.0 to 25.5
Sets the sleep function delay time in terms
of seconds. Sleep Delay Time b5-16