Sloan 910 Royal Exposed 900 Hydraulic Series - Manual (Page 6)

6
DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean flushometers that may dull the luster and attack the chrome or special decorative
finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel.
While cleaning the bathroom tile, protect the Flushometer from any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating.
Note: Behind wall access required to install HY-100-A (MBFW)
B
Screw Threaded Rod into back of Push Button Actuator.
If not already completed, bore a 1-1/2” (38 mm) diameter hole in
wall for the Push Button Actuator. Refer to the Rough-in drawings on
Pages 1 and 2.
A
C
Thread Actuator Assembly Nut onto end of Push Button Actuator.
D
Slide Spring over Metal Push Button until it snaps into place.
Insert Metal Push Button into Button Flange.
E
Place Spacer Ring over threads of Button Flange and thread
Button Flange Assembly into Actuator Assembly Nut.
F
From behind wall, run Plastic Tubing through optional Spacer Sleeve
(notched end of sleeve toward rear) and wall. Spacer Sleeve only
required if wall thickness is less than 2” (51 mm).
G Attach Plastic Tubing. See: Steps to Attach Plastic Tubing (Page 5).
H Insert Push Button Assembly into the 1-1/2” (38 mm) wall hole.
I From behind wall, slide Spacer Sleeve (if required) over Threaded Rod
and rest it against rear of wall. Slide Retaining Bar onto Threaded
Rod and into slots of Sleeve (if required), or against wall if Sleeve is
not required. Install Lockwasher and Nut onto Threaded Rod. Tighten
securely. Carefully cut excess Threaded Rod, making certain to not
damage Plastic Tubing.
Note: Use HY-108-A (MBPM) on punched stainless steel plates and
security fixtures with front access.
BUTTON FLANGE
METAL
BUTTON
SPRING
SPACER
RING
ACTUATOR
ASSEMBLY
NUT
WALL
PUSH
BUTTON
ACTUATOR
QUICK
CONNECT
FITTINGS (2)
PLASTIC
TUBING
SPACER SLEEVE —
USE ONLY IF WALL
THICKNESS IS LESS
THAN 2” (51 mm)
THREADED ROD LOCKWASHER
RETAINING
BAR
NUT
Attach plastic tubing to push button actuator. See: Steps to Attach
plastic tubing (Page 5).
A
B
Thread actuator assembly nut onto threaded end of push button
actuator.
C
Slide Spring over Metal Push Button until it snaps into place.
Insert Metal Push Button into Button Flange.
D
From front of panel, insert Button Flange Assembly into hole of panel.
Behind panel, place Washer over threads of Button Flange. Thread
Button Flange onto Actuator. Tighten Flange securely.
BUTTON FLANGE
METAL BUTTON
SPRING
PANEL
WASHER
ACTUATOR
ASSEMBLY NUT
PUSH BUTTON
ACTUATOR
QUICK CONNECT
FITTINGS (2)
PLASTIC
TUBING
Shut off control stop by turning handle
CLOCKWISE. Then remove flushometer
cover.
A
Lift out the inside parts assembly as a
complete unit. Reinstall flushometer cover
and tighten with wrench. Open control
stop. Turn on water supply to flush line of
any debris or sediment.
B
C Shut off control stop and remove flushometer
cover. Reinstall Inside Parts assembly and
flushometer cover. Tighten cover with
wrench. Open control stop and activate
flushometer.
Adjust control stop to meet flow rate required
for proper cleansing of fixture. Open control
stop COUNTERCLOCKWISE ONE FULL turn
from closed position. Activate flushometer.
Adjust control stop after each flush until the
rate of flow delivered properly cleanses the
fixture.
D
SLOAN FLUSHOMETERS ARE ENGINEERED FOR QUIET OPERATION.
EXCESSIVE WATER FLOW CREATES NOISE, WHILE TOO LITTLE WATER
FLOW MAY NOT SATISFY THE NEEDS OF THE FIXTURE. PROPER
ADJUSTMENT IS MADE WHEN TEH PLUMBING FIXTURE IS CLEANSED
AFTER EACH FLUSH WITHOUT SPLASHING WATER OUT FROM THE LIP
AND A QUIET FLUSHING CYCLE IS ACHIEVED.
NEVER OPEN CONTROL STOP TO WHERE THE FLOW FROM THE VALVE
EXCEEDS THE FLOW FROM THE VALVE EXCEEDS THE FLOW CAPABILITY OF
THE FIXTURE. IN THE EVENT OF A VALVE FAILURE, THE FIXTURE MUST BE
ABLE TO ACCOMMODATE A CONTINUOUS FLOW FROM THE VALVE.
!!! IMPORTANT !!!
6E - INSTALL PUSH BUTTON ACTUATOR (HY-100-A METAL BUTTON (MBFW VARIATION) ACTUATOR – FIXTURE WALL)
6F - INSTALL PUSH BUTTON ACTUATOR (HY-108-A METAL BUTTON (MBPM VARIATION) ACTUATOR – PANEL MOUNT)
7 - FLUSH OUT SUPPLY LINE AND ADJUST CONTROL STOP
CARE AND CLEANING OF CHROME AND SPECIAL FINISHES