Montigo ME34-DV2 - Manual (Page 2)

Page Part No. XG0105B
ME34-DV-2 Homefire
Table Of Contents
Introduction ............................................................................... 2
Installation
Installing the Fireplace Shell .......................................... 3
Installing the Gasline ...................................................... 4
The Remote Switch ........................................................ 4
Direct Vent Installation ................................................... 4
General Requirements ...................................... 4
Terminations ...................................................... 5
Top Vent Through-the-Wall Installations ............ 6
Top Vent Through-the-Roof Installations ........... 8
Rear Vent Through-the-Wall Installations .......... 9
Rear Vent Multi-Elbow Installations ................. 10
Construction around the fireplace
Facing .............................................................. 11
Mantels and Surrounds ................................... 11
Wiring .................................................................. 11 - 12
Installing the Logset ..................................................... 12
Removing and Installing the Insert ............................... 13
Removing and Installing the Door ................................ 13
Operation ..........................................................................14 - 15
Maintenance .....................................................................16 - 17
Warranty .................................................................................. 18
Appendix
A. Termination Locations .............................................. 19
CAUTIONS
Due to its high operating temperatures, the appliance
should be located out of traffic & away from furniture and
draperies.
 Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
 Young children should be carefully supervised when
they are in the same room as the appliance.
 Clothing or other flammable materials should not be
placed on or near the appliance.
Introduction
About the modular fireplaces and the ME34-DV-2 Homefire:
The ME34-DV-2 includes a 21,000 BTU dual burner, 5 piece logset,
and glowing embers. All M34 Series Modular Fireplaces allow quick
and easy upgrades in the future. The ME34-DV-2 can be upgraded
to a 25,000 BTU Homefire Plus burner. Contact your dealer for more
information. The ME34-DV-2 model is available in four versions:
 Top Vent (Product Code ME34DT-2)
 Rear Vent (Product Code ME34DR-2)
 Electronic Ignition - Top Vent (Product Code ME34DT-I-2)
 Electronic Ignition - Rear Vent (Product Code ME34DR-I-2)
The ME34-DV-2 is certified as a Vented Gas Fireplace Heater
(ANSI Z21.88-2000 · CSA 2.33-2000) and is rated for:
Natural Gas 21,000 BTU/H (7.6 Kilowatts) Maximum Input
17,500 BTU/H (5.1 Kilowatts) Minimum Input
Propane 21,000 BTU/H (7.6 Kilowatts) Maximum Input
17,500 BTU/H (5.1 Kilowatts) Minimum Input
How to use this manual:
This manual covers installation, operation and maintenance. Light-
ing, operation and care of this fireplace can be easily performed by
the homeowner. However, all installation and service work should be
performed by a qualified or licensed installer, plumber, or gasfitter
who is qualified or licensed by the state, province, region, or govern-
ing body in which the appliance is being installed.
This manual covers all models and unless otherwise specified, the
designation ME34-DV-2 refers to all models. Sections which are
specific to a particular model are marked with a symbol,
plus the appropriate model number.
Warranty and Installation Information:
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
 Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.
 Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.
 Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation require-
ments for factory-built gas fireplaces. Installation & repairs should be
done by a qualified contractor.
Installations in Canada must conform to the current CAN/CGA
B-149.1 and .2 Gas Installation Code and local regulations. If the
optional air-circulating fan kit is installed, it must be electrically
grounded in accordance with CSA C22.1 Canadian Electrical Code
Part 1 and/or Local Codes.
Installations in the USA must conform to local codes, or in the
absense of local codes to the National Fuel Gas Code, ANSI
Z223.1-1988. If the optional air-circulating fan is installed, it must be
grounded in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70-1987.