Denon ADV-M71 - Manual (Page 38)

38
ENGLISH
4 Press the ENTER button to enter the
settings.
• The next screen in the system setting
changing menu appears.
ENTER
Remote control unit
Input function settings
• LINE-1 and LINE-2 can be set as described below.
LINE-1 : “MD”, “CD-R”, “MD/CD-R” or “AUX” can be
selected.
(“MD/CD-R” can only be set when a system MD
recorder, cassette deck and CD recorder are all
connected and system operations are being used.)
LINE-2 : This can be set to “TAPE”, “MD”, “AUX” or “D.AUX”.
(Set “D.AUX” to use the D.AUX digital input in
combination with the LINE-2 analog input.)
• The setting for LINE-1 has priority. Once a function is set for
LINE-1, it is not possible to set the same function for LINE-2. (For
example, if “MD” is selected for LINE-1, “MD” is no longer
offered as one of the choices for LINE-2.)
LINE-1/LINE-2 analog recording output setting
• Normally set this to “On”.
• With the DVD or D.AUX exclusive digital input function, set this
to “Off” if noise is generated when playing sources with high bit
rates in the Dolby Virtual Speaker mode.
• This setting is only valid in the Dolby Virtual Speaker mode for the
DVD or D.AUX exclusive digital input function. (In surround
modes other than the Dolby Virtual Speaker mode and with other
input functions, analog recording signals are output, regardless of
this setting.)
• Analog recording is not possible when this is set to “Off”. To
record, use a mode other than the Dolby Virtual Speaker mode
(stereo, for example).
(4) After changing the system settings
• This completes the procedure for changing the system settings.
Once the speaker settings, delay times and channel levels have
been set, there is no need to change the settings again unless the
connected AV components or speakers are changed or the
speakers are moved to different positions.
• DVD auto power off and function settings as necessary.
1 At the system setting changing menu
screen, press the SETUP button.
• The new settings are entered and the
on-screen display turns off.
SETUP
Remote control unit
The setup procedure can be quit at any point by pressing this
button.
NOTE:
• When system settings have been changed with the system
setting changing menu and a speaker system is selected with
the quick system settings, the speaker settings and delay time
settings are changed to the values preset for the quick system
settings.
B
BAND
PHONES
VOLUME
ON / STANDBY
DVD SURROUND RECEIVER ADV-M71
TONE / SDB
FUNCTION
MENU / SET
+ -
SURROUND / SELECT PUSH - PARAM.
VIRTUAL SPEAKER
2
+
-
+
-
RC-936
A / V
3
A-B REPEAT
SEARCH MODE
ON OFF
REPEAT RANDOM
CLEAR ZOOM SLIDE MODE
PROG/DIRECT
MEMO BAND MODE
STATUS
RETURN
ANGLE AUDIO SUB TITLE
SETUP TONE /SDB
FUNCTION SURROUND INPUT MODE TEST TONE
DVD
TUNER
CH
3
- +
2 1
6 5 4
9 8 7
0 /10 CALL
ENTER
MUTING
+10
DISPLAY MENU TOP MENU
SYSTEM MD
CDR TAPE
TUNER TV / VCR
SURROUND PARAMETER CH SELECT
VCR
NTSC/PAL SLEEP
ENTER
CD SRS
EDIT/MENU CHARAC.
REC TIME TITLE
TUNING / TV VOL
TV CH TV CH
TUNER DVD
MD/LINE-1 TAPE /LINE-2
AUTO DECODE
VIRTUAL DIRECT
5CH STEREO
STEREO
D.AUX
- + VCR CH
IN/SURR.
IN/SURR.
DVD
T V TV IN SOURCE
9 8
2 1
7 6
+
-
2
(1) Before Operating
11 PLAY BACK
1 Refer to “CONNECTIONS” (pages 8 to 15) and check that all
connections are correct.
2 Turn on the power.
Press the POWER
button.
When pressed, the power turns on and the display lights. The
sound is muted for several seconds, after which the unit
operates normally. When pressed again, the power turns off,
the standby mode is set and the display turns off.
Whenever the ON/STANDBY button is in the STANDBY state,
the apparatus is still connected on AC line voltage. Please be
sure to unplug the cord when you leave home for, say, a
vacation.
ON / STANDBY
ON
Light
(green)
Main unit Remote control unit