Top Flite TOPA0140 User Manual
Page 6

❏
3/32" [2.4mm] Wheel Collar for tailwheel
(GPMQ4302)
❏
12 oz. [360cc] Fuel Tank (GPMQ4105)
❏
24" [610mm] Medium Silicone Fuel Tubing
(GPMQ4131)
❏
Fuel Filler Valve (GPMQ4160)
❏
3-1/2" [89mm] Spinner,
see Scale propeller and
spinner section on page 53
❏
1/4" [6mm] R/C Foam Rubber Padding
(HCAQ1000)
❏
Pilot Figure (WBRQ2476) (a 1/7-scale pilot
figure is optional if the cockpit kit is used)
❏
Exhaust Deflector (HCAP2175)
❏
2 - 3 rolls Top Flite Super MonoKote covering,
see page 50
❏
Paint, see page 51
❏
Propellers, see the instructions with your engine
BUILDING SUPPLIES
Here is a check list of supplies you should have on
hand while building. We recommend Great Planes
Pro™ CA and Epoxy.
❏
2 oz. [60g] Thin CA (GPMR6003)
❏
2 oz. [60g] Medium CA+ (GPMR6009)
❏
2 oz. [60g] Thick CA- (GPMR6015)
❏
CA Accelerator (GPMR6035)
❏
CA Debonder (GMPR6039)
❏
CA Applicator Tips (HCAR3780)
❏
6-minute epoxy (GPMR6045)
❏
30-minute (GPMR6047)
❏
Pro Wood Glue (GPMR6161)
❏
J & Z Products
Z RC/56 canopy glue
(JOZR5007)
❏
Microballoons (TOPR1090)
❏
Milled Fiberglass (GPMR6165)
❏
Lightweight Hobby Filler (HCAR3401)
❏
Auto body filler (Bondo
®
or similar)
❏
Denatured or Isopropyl Alcohol (to clean up
excess epoxy)
❏
Masking Tape (TOPR8018, 8014, 8012)
❏
Wax Paper or Plan Protector (GPMR6167)
❏
#11 Blades (HCAR0311, 100 qty.)
❏
Single-Edge Razor Blades (HCAR0312, 100 qty.)
❏
T-Pins small (HCAR5100), medium (HCAR5150),
large (HCAR5200)
TOOLS
❏
Sealing iron (TOPR2100)
❏
Razor Plane (MASR1510)
❏
Hobbico Builder’s Triangle (HCAR0480)
❏
Drill Bits:
1/16" [1.60mm]
#48 [1.95mm] (or 5/64"),
3/32" [2.40mm]
9/64" [3.60mm] (or 1/8"),
1/8" [3.10mm]
5/32" [4.00mm]
3/16" [4.70mm]
7/32" [5.60mm]
1/4" [6.30mm]
17/64" [6.70mm]
#10 [4.90mm] or 13/64"
(or 1/4-20 tap and drill set)
#29 [3.40mm] or 9/64"
(or 8-32 tap and drill set)
❏
1/4-20 Tap and drill (GPMR8105)
❏
8-32 Tap and drill (GPMR8103)
❏
Tap wrench (GPMR8120)
❏
Kyosho
®
Lexan
®
Curved Scissors (KYOR1010)
❏
Long handle 9/64" ball end hex wrench
(GPMR8004)
❏
Silver Solder (GPMR8070 w/flux)
❏
Easy–Touch
™
Bar Sanders
❏
Heat Gun (TOPR2000)
❏
Trim Seal Tool (TOPR2200)
❏
Sealing Iron (TOPR2100)
❏
Hot Sock
™
(TOPR2175)
EASY-TOUCH BAR SANDER
A flat, durable, easy-to-handle sanding tool is a
necessity for building a well finished model. Great
Planes makes a complete range of Easy-Touch
Bar Sanders (patent pending) and replaceable
Easy-Touch Adhesive-backed Sandpaper. While
building the Spitfire we used two 5-1/2" [140mm]
bar sanders and two 11" [280mm] bar sanders
equipped with 80-grit and 150-grit adhesive-backed
sandpaper. Here is the complete list of Easy-Touch
Bar Sanders and adhesive-backed sandpaper:
5-1/2" [140mm] (GPMR6169)
11" [280mm] (GPMR6170)
22" [560mm] (GPMR6172)
33" [835mm] (GPMR6174)
44" [1118mm] (GPMR6176)
Contour Multi-Sander
11" [280mm] (GPMR6190)
The Easy-Touch Adhesive-Backed Sandpaper is
available in 2" x 12' rolls:
80-grit (GPMR6180)
150-grit (GPMR6183)
220-grit (GPMR6185)
Assortment of 5-1/2" [140mm] strips (GPMR6189)
We also use 320 or 400-grit wet-or-dry sandpaper
for finish sanding.
- 6 -